CompTIA PD1-001 PDI+ Beta Certification Practice Exam Set 8

On a CMYK output device, if the cyan level were increased, which of the following might be a side effect?


Options are :

  • Yellow may appear less saturated
  • All other colors would have a dark halo
  • Red may appear less saturated
  • Green may appear more saturated

Answer : Green may appear more saturated

A customer wants to use a USB printer on their network. They do not want to use the resources on any computer because is would cause the computer to slow down. Which of the fol owing should the technician recommend?


Options are :

  • Convert the network to wireless.
  • Purchase a new printer with a NIC.
  • Install an external USB print server.
  • Purchase a parallel adapter for the printer.

Answer : Install an external USB print server.

On a CMYK output device, if the yellow level were increased, which of the following mightbe a side effect?


Options are :

  • Orange may appear less saturated
  • All other colors would have a dark halo
  • Red may appear more saturated
  • Blue may appear less saturated

Answer : Orange may appear less saturated

Which of the following is a common form of memory card used to store information?


Options are :

  • OS
  • SD
  • RAW
  • LPT

Answer : SD

The technician servicing a MFP suspects that the fuser lamp may have failed. Which of the fol owing steps will confirm this?


Options are :

  • Plug the lamp directly into an outlet, bypassing the MFPs internal components.
  • Replace the lamp with a new one.
  • Check the lamps continuity using an ohmmeter.
  • Hold the lamp up to the light to see if the filament is intact.

Answer : Check the lamps continuity using an ohmmeter.

CompTIA JK0-801 A+ Certification Practical Exam Set 3

Which of the following is a recommended cleaner for rubber feed rollers?


Options are :

  • Water
  • Iodine
  • Bleach
  • Glass cleaner

Answer : Water

Which of the fol owing connection types was designed for integrated circuits in which a minimal amount of force is needed to make the connection without the use of a special tool?


Options are :

  • Mini molex
  • Spring contacts
  • Molex
  • ZIF

Answer : ZIF

Which of the following troubleshooting steps would aid in dealing with an issue that might be faced repeatedly in the future with another device?


Options are :

  • Use service documentation
  • Isolate the problem
  • Document results
  • Validate the solution

Answer : Document results

A customer reports that some of their documents have extra spaces between the paragraphs. Which of the following is the MOST likely cause of this issue?


Options are :

  • Wrong network port
  • Port 9100 is turned off
  • Incorrect Driver
  • Device is offline

Answer : Incorrect Driver

A customer just bought a new PC with the latest operating system. They disconnected their currently functional three year old MFD from their old PC and connected/installed it on the new PC using the original set of drivers. They can print fine but have lost scanning ability. Which of the following is the cause of this issue?


Options are :

  • The scanner driver is not supported by the new operating system.
  • The scanner driver is corrupted.
  • The scanner is defective and needs new firmware.
  • The new operating system is improperly installed.

Answer : The scanner driver is not supported by the new operating system.

Which of the fol owing is a method of increasing the visual impression of blue when printing on a CMYK printer?


Options are :

  • Increase the level of C in the print driver.
  • Increase the level of K in the print driver.
  • Increase the level of CMYK equal y.
  • Increase the level of Y in the print driver.

Answer : Increase the level of C in the print driver.

CompTIA 220-801 A+ Advanced Certification Practice Exam Set 8

Which of the following is a reason for using Xenon or fluorescent scan lamps in MFD devices?


Options are :

  • Xenon and fluorescent scan lamps have low temperature and even light spread.
  • Xenon and fluorescent scan lamps are better for the environment.
  • Xenon and fluorescent scan lamps are less subject to breakage.
  • Xenon and fluorescent scan lamps produce only one color of light.

Answer : Xenon and fluorescent scan lamps have low temperature and even light spread.

Which of the following forms will describe hazards and other properties of toner?


Options are :

  • Configuration report
  • Network Settings report
  • MSDS
  • Printer quality pages

Answer : MSDS

While printing the customer receives a message XG2 Call Service on the display of the device, where should the technician FIRST look for information on this message?


Options are :

  • Printer test page
  • Cal technical support
  • Users Manual
  • Service manual

Answer : Service manual

Which of the following components is MOST likely to require lubrication?


Options are :

  • Plastic levers
  • Rubber rollers
  • Metal Gears
  • Nylon Belts

Answer : Metal Gears

When an image is scanned, which of the following is the image FIRST created as?


Options are :

  • Digital
  • Compression
  • Network
  • Analog

Answer : Analog

When scanning in color which of the following model is being utilized?


Options are :

  • CMYK
  • Mono
  • Subtractive
  • RGB

Answer : RGB

SK0-004 CompTIA Server+ Certification Practice Exam Set 9

A customer calls for technical support and complains that their color laser MFD always puts a line on the page. Which of the following should a technician ask the customer?


Options are :

  • How much paper is left in the tray?
  • What color is the line?
  • What mode of operation is being used at the time it occurs?
  • When was the last time you cleaned the photoconductor?
  • Is your machine indicating a low toner message?

Answer : What color is the line? What mode of operation is being used at the time it occurs?

Which of the following BEST describes the developing stage?


Options are :

  • Toner is heated.
  • Developer is purged from the developer unit.
  • Toner is attracted to the latent image.
  • Developer and toner are cleaned of paper dust.

Answer : Toner is attracted to the latent image.

Which of the following is the typical reason for installing a Hard Drive to the scanner section of an MFP?


Options are :

  • To increase the color gamut of the scanner.
  • To enable the image compression feature on the MFP.
  • To increase the amount of images that can be scanned into memory.
  • To enable the negative image scanning feature on the MFP.

Answer : To increase the amount of images that can be scanned into memory.

A customer complains that in their office the prints look fine, but at their client's office the same document looks different. Which of the following should the technician tell the customer?


Options are :

  • The clients office does not have the correct climate control.
  • Bringing the document into the sun fades the color.
  • The papers texture has been altered.
  • The type of light used at an office affects how color looks.

Answer : The type of light used at an office affects how color looks.

The customer reports that their MFP jams from one paper source, but works properly from the others. How can the technician begin to resolve the issue?


Options are :

  • Review the error logs for what types of errors the device has had.
  • Replace the paper feed rollers.
  • Replace the failed tray with a new one.
  • Limit the customer to use only the working paper sources.

Answer : Review the error logs for what types of errors the device has had.

A technician finds the printer with many loose power and network cables creating a potential trip hazard. Which of the following is the BEST step to correct this situation?


Options are :

  • Move the printer to a different location.
  • Re-route and secure all the cables.
  • Inform the customer about the issue.
  • Tape the cables to the carpet with bright colored tape.

Answer : Inform the customer about the issue.

CLO-001 CompTIA Cloud Essentials Certification Practice Test Set 2

Which of the following is used to adjust the exposure on a scanner?


Options are :

  • The scanner speed
  • Image processor
  • The mirror
  • Exposure lamp voltage

Answer : Image processor

Which of the following components is used for transmitting drive energy?


Options are :

  • Micro switches
  • Gears
  • Encoder
  • Solenoid

Answer : Gears

Which of the fol owing would explain why the customer may see a difference between thecolor on their workstation screen and the output from their CMYK printer?


Options are :

  • The workstation screen transmits light while the printed images reflect light.
  • The workstation screen reflects light while the printed images transmit light.
  • The toner in the printer needs replacing with fresh cartridges.
  • The screen on the workstation needs turning up a little brighter.

Answer : The workstation screen transmits light while the printed images reflect light.

Which of the following is a scanner driver?


Options are :

  • SMB
  • Telnet
  • FTP
  • TWAIN

Answer : TWAIN

A technician arrives at a client location to repair a device. The technician speaks with the primary user about the issues and goes to the device and duplicates the problem. Which of the following troubleshooting steps has the technician accomplished?


Options are :

  • Isolate the problem and use service tools.
  • Validate the problem and implement solutions.
  • Gather information and evaluate symptoms.
  • Validate the solution and document actions.

Answer : Gather information and evaluate symptoms.

A customer cal s technical support and states that they have read their laser printer users guide and learned that it has a watermarks feature. They followed all the steps in the guide but cannot find the feature anywhere. Which of the following should the technician have the customer do FIRST?


Options are :

  • Use another application.
  • Power cycle the print On/Off.
  • Uninstall/reinstall the driver.
  • Verify the driver version installed.

Answer : Verify the driver version installed.

CompTIA Network+ (N10-007) 6 Practice Exams and Simulations Set 1

Which of the following is a physical port referred to as IEEE 1394 used to connect a device?


Options are :

  • SD
  • Serial
  • LPT
  • FireWire
  • USB

Answer : FireWire

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions