CompTIA PD1-001 PDI+ Beta Certification Practice Exam Set 7

Which of the following is MOST likely to require a firmware upgrade?


Options are :

  • Changing the IP address and subnet mask
  • Adding two new media sizes to the control panel
  • Installing an updated printer driver
  • Adding 256MB of RAM

Answer : Adding two new media sizes to the control panel

Which of the following components contains the second and third mirrors in a cabledrive flatbed scanner?


Options are :

  • CCD
  • Second mirror assembly
  • First mirror assembly
  • ADF

Answer : Second mirror assembly

Which of the following is the purpose of the cover that is used to conceal the lens and CCD in the flatbed scanner?


Options are :

  • To reduce wear and tear on the components.
  • To allow the components to reach operating temperature faster.
  • To reduce paper dust contamination.
  • To block stray light from altering the scanned image.

Answer : To block stray light from altering the scanned image.

Which of the following copy defects would result from the scanner carriage being


Options are :

  • Image edges wil resemble a parallelogram
  • Overall light copy quality
  • Overall image wil be skewed
  • Overall dark copy quality

Answer : Image edges wil resemble a parallelogram

A customer reported streaks on copies when using the document glass, but notwhen feeding originals through the ADF. To resolve this issue the technician should:


Options are :

  • troubleshoot the print engine.
  • clean the exposure glass.
  • clean the slit glass.
  • clean the ADF feed rollers.

Answer : clean the exposure glass.

CompTIA Advanced Security Practitioner(CASP+) Practice Exams Set 4

Which of the following copy defects would result from a large black mark on the slitg lass when using the ADF?


Options are :

  • White streak on the copy
  • Overall light copy quality
  • Black spots on the copy
  • Black streak on the copy

Answer : Black streak on the copy

Which of the following describes the purpose of multi-jointed ADF hinges?


Options are :

  • To allow duplex scanning
  • To reduce wear and tear on the hinges
  • To allow the scanning of books
  • To make the ADF easier to raise

Answer : To allow the scanning of books

Which of the following electrical components converts AC source voltages to various DC voltages?


Options are :

  • LVPS
  • CCD
  • PRCB
  • HVPS

Answer : LVPS

The firmware for a multifunction device equates to which of the following on a PC?


Options are :

  • RAM
  • Application software
  • Operating system
  • Hard drive

Answer : Operating system

Which of the following electrical components utilizes infrared LEDs to detectswitching or a change of state?


Options are :

  • Switch
  • Resistor
  • Capacitor
  • Sensor

Answer : Sensor

Which of the following is the purpose of the manual feed knob in the ADF?


Options are :

  • To adjust the separator pad
  • To calibrate the ADF feed rollers
  • To remove paper jams safely
  • To adjust the platen glass

Answer : To remove paper jams safely

SK0-004 CompTIA Server+ Certification Practice Exam Set 3

Which of the following components contains multiple rollers for transporting originals?


Options are :

  • CCD
  • ADF
  • Flatbed scanner
  • Platen glass

Answer : ADF

Which of the following electrical components is used to protect against excessive


Options are :

  • Fuse
  • Thermistor
  • Resistor
  • Capacitor

Answer : Fuse

A technician is onsite troubleshooting a networked print device. The device does not seem to be connecting properly to other devices on the network. The technician takes a crossover cable and attaches the cable to the printer and the PC and it prints properly. Which of the fol owing could be the cause of this situation?


Options are :

  • The PCs NIC has failed.
  • A network switch or hub has failed.
  • The NIC of the printing device has failed.
  • The print driver is faulty.

Answer : A network switch or hub has failed.

A customer is printing on plain standard size envelopes with their monochrome laser printer using a word processing application envelope tool. They have chosen the correct size and orientation but the address is ghosting on the printed envelopes. Which of the fol owing should resolve this issue?


Options are :

  • Select the bypass option in the device driver.
  • Select the correct media type in the device driver.
  • Select the face-up orientation in the application tool.
  • Select a different envelope size in the application tool.

Answer : Select the correct media type in the device driver.

RGB color model is used mainly by which type of device?


Options are :

  • Scanner
  • Dot Matrix Printer
  • Impact Printer
  • Monitor
  • Color Printer

Answer : Scanner Monitor

Which of the following components is used for raising and lowering high capacity paper trays?


Options are :

  • Cables
  • . Feed unit
  • Separator pad
  • Paper feed clutch

Answer : Cables

220-802 CompTIA A+ Certification Practice Exam Set 2

Which of the following parts of the fuser should a technician never touch with their bare hands?


Options are :

  • Separator pawls
  • Halogen lamp
  • Thermistor
  • Heat Roller

Answer : Halogen lamp

Which of the fol owing would be the MOST suitable method of printing for a small office with four workstations and one MFD?


Options are :

  • Use only one workstation for printing to avoid confusion.
  • Network with a print driver loaded on each workstation.
  • Connect via a parallel cable through a hub out to each workstation.
  • Connect via a serial cable through a hub to the print device.

Answer : Network with a print driver loaded on each workstation.

When measuring ohms using a multimeter a technician is measuring which of the following?


Options are :

  • Capacitance
  • Current
  • Resistance
  • Voltage

Answer : Resistance

Which of the following is used for reducing output from an MFP evenly in feed and crosswise directions?


Options are :

  • Moving the scanner optic mirror closer to the reduction lens
  • Change the speed of the photoconductor
  • Image processor circuitry
  • Moving the scanner optic mirror away from the reduction lens

Answer : Image processor circuitry

Which of the following do printer manufactures use to help reduce ozone in the air?


Options are :

  • Filter
  • Corona Wire
  • Charge Corona
  • Firewall

Answer : Filter

The customer is printing a manual that is in color, with many graphics and in a PDF format. But when the document prints, some of the pages come out with random characters and the graphics are missing. Which of the following can the technician advise the customer to do?


Options are :

  • Make sure the customer is using a post script driver.
  • Try printing in monochrome mode to see if the documents are correct.
  • Have the customer reboot both the printer and the PC, so they can synchronize together.
  • Make sure the paper loaded is designed for graphics.

Answer : Make sure the customer is using a post script driver.

CompTIA JK0-801 A+ Certification Practical Exam Set 5

When an image is scanned it is focused onto which of the following components?


Options are :

  • Charge roller
  • CCD
  • Lens
  • Transfer belt

Answer : CCD

A customer wants their logo to be copied "more blue." According to the technician's test charts the colors are adjusted properly. Which of the following should the technician advise?


Options are :

  • Adjusting the device to enhance the blue wil affect the other colors.
  • The cyan photoconductor needs to be replaced to make the copies more blue.
  • The color calibration needs to be carried out more frequently.
  • The magenta toner needs to be replaced to make the copies more blue.

Answer : Adjusting the device to enhance the blue wil affect the other colors.

During the writing stage of the print process, which of the following creates the latentimage on the photoconductor?


Options are :

  • Laser unit
  • Developer Unit
  • CCD unit
  • CIS unit

Answer : Laser unit

A user reports that they cannot print, which of the following is the next step?


Options are :

  • Check the RJ-11 cable
  • Check port 9100
  • Set network port to10MB
  • Check if other workstations can print

Answer : Check if other workstations can print

A customer has complained of intermittent white streaks on copies from a MFD. Which of the following questions would help the technician isolate the issue?


Options are :

  • Does the streak only appear on color copies?
  • What software application is being used?
  • What version of print driver is being used?
  • What type of computer are you using?

Answer : Does the streak only appear on color copies?

A customers copier says Add Paper even though the paper tray is full. Where MOST likely is the cause of the problem?


Options are :

  • The paper tray is set to a different paper size than requested.
  • The sensor that tells the copier the tray is ful is broken or has failed.
  • The customer has left the original on the platen glass.
  • The sensor in the duplex section shows paper already there.

Answer : The sensor that tells the copier the tray is ful is broken or has failed.

CompTIA JK0-019 E2C Network Media & Topologies Practice Exam Set 1

A customer complains that a color device is always calibrating. Which of the following is the BEST explanation about the issue?


Options are :

  • The RGB gammas need to be downloaded to the hard drive.
  • Paper trays need to be adjusted periodically.
  • The device is updating the network settings.
  • Changes in the environment change color output.

Answer : Changes in the environment change color output.

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions