CompTIA PD1-001 PDI+ Beta Certification Practice Exam Set 4

The purpose of the constant voltage supplied to a photo interrupter type sensor used in conjunction with a ground, is to:


Options are :

  • switch the voltage going to frame ground.
  • energize the LED.
  • provide a voltage to the base of the photo transistor.
  • send a signal voltage to the controller PCB.

Answer : energize the LED.

A client is printing a document they have received from one of their vendors on a LAN printing device. The document prints in landscape even though the printer is hard set to portrait mode and other documents print portrait. Which of the following could be the problem?


Options are :

  • The page setup associated with the document in the application is set to landscape.
  • The print driver on their system is defaulting to landscape mode for that particularapplication.
  • The print queue is set to landscape as default.
  • The printers local defaults are set to landscape mode.

Answer : The page setup associated with the document in the application is set to landscape.

Which of the following adjustments should the technician make to produce a gray with les red in it?


Options are :

  • Reduce magenta and yellow in the color balance.
  • Reduce magenta and cyan in the color balance.
  • Increase blue and reduce yellow in the color balance.
  • Increase black and reduce yellow in the color balance.

Answer : Reduce magenta and yellow in the color balance.

A technician has finished changing the developer material in a multifunction device. Which of the following is the BEST way to handle the old developer material?


Options are :

  • Pour the old developer material into the trash can and throw in an incinerator.
  • Pour the old developer back into the original packaging and dispose of properly.
  • Use the vacuum cleaner to remove the old developer material.
  • Take the old developer back to the office to be refurbished.

Answer : Pour the old developer back into the original packaging and dispose of properly.

Which of the following components are used to provide recoil, tension and pressure?


Options are :

  • Gear
  • Spring
  • Bushing
  • Bearing

Answer : Spring

A customer is not able to print to their color printer. The technician notices that the LED son the NIC are off. Which of the following would MOST likely cause this problem?


Options are :

  • Corrupted Firmware
  • Incorrect SMTP settings
  • Printer set for black and white
  • Damaged cable
  • Defective RJ-45 connector

Answer : Damaged cable Defective RJ-45 connector

JK0-015 CompTIA E2C Security+ 2008 Edition Practice Exam Set 9

Which of the fol owing components would be used in conjunction with an interrupt sensor if counting pulses is required?


Options are :

  • AC moter
  • ENcoder
  • DC moter
  • Solenoid

Answer : ENcoder

Which of the following components is typically used to detect the locations of the mediatray position guides?


Options are :

  • Micro switches
  • Bearings
  • Encoders
  • Clutches

Answer : Micro switches

Which of the following wil happen if the photoconductor has prolonged exposure to sunlight?


Options are :

  • Weakens the photoconductor
  • Softens the photoconductor
  • Increased sensitivity of the photoconductor
  • Hardens the photoconductor surface

Answer : Weakens the photoconductor

The purpose of a solid state relay is to:


Options are :

  • adjust the DC voltage on a power supply.
  • operate a door switch on the MFD.
  • use an AC voltage to switch on the image processor.
  • use a DC signal voltage to switch an AC voltage.

Answer : use a DC signal voltage to switch an AC voltage.

Which of the fol owing components requires a tension pulley to remove excess slack on MOST machines?


Options are :

  • Bearing
  • Belt
  • Roller
  • Gear

Answer : Belt

Which of the following processes occurs inside the laser unit during printing?


Options are :

  • The mirrors and lenses are cleaned.
  • The polygon mirror spins at operating RPM.
  • The laser beam is charged by the charge roller.
  • The beam detector temperature is measured.

Answer : The polygon mirror spins at operating RPM.

CompTIA JK0-801 A+ Networking & PC Hardware Practice Exam Set 4

Which of the following are types of network ports?


Options are :

  • Port 9100
  • GDI
  • LPR
  • SMB
  • IDE
  • PCL

Answer : Port 9100 LPR SMB

Which of the following would be responsible for the network device printing random characters on the print jobs?


Options are :

  • The paper tray is empty.
  • The toner is not properly installed.
  • The photoconductor is damaged.
  • The driver is corrupted.

Answer : The driver is corrupted.

Which of the following component types are used by scanners for capturing images?


Options are :

  • LED
  • CIS
  • LCD
  • CCD
  • NIC

Answer : CIS CCD

A technician encounters an extremely irate client. During initial conversation the client makes it clear they are very angry with the situation and the technician. The client becomes aggressive, unreasonable, verbally abusive, loud and very rude to the technician. Which of the responses below is the BEST way to react?


Options are :

  • Politely and quietly, turn around and leave. The technician should immediately contacttheir management to inform them of the situation and have them follow up with the clientscompany.
  • Walk over to the device and disassemble it. Then turn around and leave while telling theclient to repair the unit themselves.
  • Try to reason with and calm the client by explaining why the unit could havemalfunctioned, how long it will take to repair the unit and how the situation is not as bad asthe client perceives it to be.
  • Explain how the issue is not the technicians fault and the client needs to step away andlet the device be assessed so the issue can be fixed.

Answer : Politely and quietly, turn around and leave. The technician should immediately contacttheir management to inform them of the situation and have them follow up with the clientscompany.

Which of the following describes the process of ensuring that all four color images are aligned?


Options are :

  • Color registration
  • Color calibration
  • Color development
  • Color exposure

Answer : Color registration

Which of the following is usually associated with a PPD?


Options are :

  • PCL
  • TCP/IP
  • PJL
  • Postscript

Answer : Postscript

CompTIA JK0-015 E2C Security+ Certification Practice Test Set 21

Which of the following components would typically move a diverter gate?


Options are :

  • DC moter
  • Solenoid
  • Cluth
  • Stepper motor

Answer : Stepper motor

Which of the following describes purging?


Options are :

  • It is the process of cleaning nozzles and ejectors in an ink dispersion printing system.
  • It is the process of clearing excess toner off the electrostatic surface in a laser/LEDprinting system.
  • It is the process of a vacuum preparing the print bed before the application of liquidcolor in a solid/block media printing system.
  • It is the process of eliminating waste ink produced during the printing process in an inkdispersion printing system.

Answer : It is the process of cleaning nozzles and ejectors in an ink dispersion printing system.

Which of the following multimeter settings should be used to measure the outputs of the LVPS?


Options are :

  • DC volts
  • Diode check
  • Resistance
  • AC volts

Answer : DC volts

Which of the following is the proper hierarchy of device settings when printing?


Options are :

  • Printer overrides driver, drive overrides application
  • Driver overrides application, application overrides printer
  • Driver overrides printer, printer overrides application
  • Application overrides driver, driver overrides printer

Answer : Application overrides driver, driver overrides printer

In order for a color scanning device to be able to capture the colors of an original document, which of the following items must be incorporated into the scanners technology?


Options are :

  • RGB color CCD filters
  • CMYK analog processor
  • CMYK color digital processor
  • RGB/CMYK color scanning lamp

Answer : RGB color CCD filters

A technician has been called to a device giving poor copy quality issues. The techniciantests the machine but is unable to recreate the issue. Which of the following should thetests the machine but is unable to recreate the issue. Which of the following should thetechnician do next?


Options are :

  • Call technical support for further advice or suggestions.
  • Speak with the customer to see if the issue was caused by a specific original.
  • A. Replace all the consumables and see if the issue occurs again.
  • Replace the photoconductor as this part often causes poor quality copies.

Answer : Speak with the customer to see if the issue was caused by a specific original.

CAS-001 CompTIA Advanced Security Practitioner Practice Exam Set 4

A technician prints a test page, measures the distance between repeating defects, and consults the service manual to determine which component is faulty. Which of the following troubleshooting steps is the technician doing when they consult the service manual?


Options are :

  • Determine next steps taken
  • Establish a theory
  • Implement a solution
  • Test or analyze

Answer : Determine next steps taken

Which of the following processes occurs inside the laser unit prior to every scan line during printing?


Options are :

  • The laser beam is detected just prior to exposing the photoconductor.
  • The laser beam is projected through the thermistor onto the photoconductor.
  • The laser beam is modulated to the charge roller rotation.
  • The laser beam is measured for proper operating temperature.

Answer : The laser beam is detected just prior to exposing the photoconductor.

Which of the fol owing multimeter settings should be used to measure source voltage at the wall outlet?


Options are :

  • AC voltage
  • Resistance
  • DC voltage
  • Diode check

Answer : AC voltage

After installing a printer driver, which of the following is the BEST way to confirm basic printing functionality?


Options are :

  • Print the driver test page
  • PING the printer
  • Display the printers embedded web server
  • Print a document from a word processing application

Answer : Print the driver test page

The drive between the input side and the output side of an electromechanical clutch is transmitted by:


Options are :

  • gear ratio and current.
  • friction and gear ratio.
  • magnetism and friction.
  • magnetism and gear ratio.

Answer : magnetism and friction.

The customer has a dedicated ink jet fax machine that is used to send and receive faxes only from the corporate office. The user complains of streaks on the received faxes while the internal self-prints are fine. Which of the following should a technician recommend?


Options are :

  • Clean the printer head on the local machine.
  • Call the telephone company to increase the line signal level.
  • Clean the scanner glass on the local machine.
  • Clean the scanner glass on the distant machine.

Answer : Clean the scanner glass on the distant machine.

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions