Citrix 1Y0-731 Netscaler 8.0 Administration Practice Test Set 2

Scenario: An administrator wants to configure a health check for a server receiving HTTP traffic. The server is usually close to its maximum capacity so the administrator wants to configure the health check so that it monitors the responses of a server to actual client requests as opposed to probes whenever possible. How can the administrator configure the health check to meet this requirement?


Options are :

  • Configure an HTTP-Inline monitor. (Correct)
  • Use a TCP monitor with the transparent parameter selected.
  • Configure an HTTP monitor with the transparent parameter selected.
  • Configure an HTTP-ECV monitor.
  • Use the default TCP monitor.

Answer : Configure an HTTP-Inline monitor.

Citrix 1Y0-731 Netscaler 8.0 Administration Practice Test Set 1

An administrator should configure Link Aggregation on a NetScaler system when __________ (Choose the correct option to complete the sentence.)


Options are :

  • redundancy is required (Correct)
  • network connections between LAN switches and network servers require more than 8 Gb/sec
  • network connections between LAN switches and network servers require more than 10 Gb/sec
  • redundancy on an operation across multiple data rates is required

Answer : redundancy is required

Which information does an administrator need to get from the Dashboard to determine the bandwidth utilization of a virtual server?


Options are :

  • Current client connections vs. current server connections
  • Request bytes vs. response bytes (Correct)
  • Current client connections vs. current clientEst connections
  • Requests vs. responses

Answer : Request bytes vs. response bytes

Which event would trigger a failover in a High Availability pair?


Options are :

  • The default gateway does not return a heartbeat packet from the primary node.
  • The primary appliance is upgraded. (Correct)
  • A forced synchronization event fails.
  • A monitored interface fails on the secondary node.

Answer : The primary appliance is upgraded.

Citrix 1Y0-351 NetScaler 10.5 Essentials and Networking Exam Set 10

Scenario: A security administrator wants to monitor the rate at which unacknowledged SYN packets are received by the NetScaler system for individual VIP addresses. The administrator plans to configure SNMP on the NetScaler to be informed about synflood rates. Which two alarms must the administrator configure in SNMP for this scenario?


Options are :

  • synfloodNormal
  • entitySynfloodNorm (Correct)
  • synflood
  • entitySynflood (Correct)

Answer : entitySynfloodNorm entitySynflood

An administrator plans to use Subnet IP addresses instead of the mapped IP address for connections to local resources. Which command should the administrator use to configure this setting?


Options are :

  • add ns mode USNIP
  • enable ns mode USNIP (Correct)
  • set ns ip snip -mip
  • set ns mode USNIP

Answer : enable ns mode USNIP

Which two events could cause two NetScaler devices to constantly trade primary state in a High Availability pair?


Options are :

  • Management interface flapping
  • Saturating the link used to exchange heartbeat (Correct)
  • Switches performing spanning tree rE. convergence (Correct)
  • Upstream routers becoming unavailable
  • Services becoming unavailable

Answer : Saturating the link used to exchange heartbeat Switches performing spanning tree rE. convergence

Citrix 1Y0-350 NetScaler 10 Essentials and Networking Exam Set 3

Scenario: A company is deploying a NetScaler system in a network environment with some subnets open to the public Internet and one non-routable subnet. The administrator plans on enabling UsE. Subnet-IP mode and disabling UsE. SourcE. IP mode. Which two IP addresses can the administrator set as source IP addresses for connections to back-end servers?


Options are :

  • MIP (Correct)
  • SNIP (Correct)
  • NSIP
  • VIP

Answer : MIP SNIP

Scenario: An administrator has created a policy expression to identify URLs with a cascaded style sheets (CSS) suffix. The administrator plans to use the policy expression to prevent URLs with a CSS suffix from being compressed when the HTTP response is received. How can the administrator associate the policy expression and action to achieve the desired result?


Options are :

  • Add a filter with the policy expression and the action specified, then bind the policy with the appropriate priority.
  • Configure the action, then add a compression policy with the policy expression and the action specified.
  • Add a compression policy with the policy expression and action specified, then bind the policy with the appropriate priority. (Correct)
  • Configure the action, then add the filter with the policy expression and the action specified.

Answer : Add a compression policy with the policy expression and action specified, then bind the policy with the appropriate priority.

Which information from the Dashboard will provide a clear indicator to an administrator that a service is definitely not able to handle the workload as configured?


Options are :

  • Current request rate
  • Current client connections
  • Current requests in the surge queue (Correct)
  • Current load on the service

Answer : Current requests in the surge queue

Citrix 1Y0-371 Designing Deploying Managing Citrix Exam Set 2

An administrator should configure Link Aggregation on a NetScaler system when ___________ (Choose the correct option to complete the sentence.)


Options are :

  • redundancy on a half duplex operation is required
  • network connections between LAN switches and network servers require more than 8 Gb/sec
  • network connections between LAN switches and network servers require more than 1 Gb/sec (Correct)
  • redundancy on an operation across multiple data rates is required

Answer : network connections between LAN switches and network servers require more than 1 Gb/sec

Scenario: A virtual hosting environment requires that the HTTP requests carry the appropriate domain name in the host header. The administrator needs to configure monitoring so that the HTTP probes carry the appropriate domain name in the host header. What are two monitor types that must be configured to meet the needs of this environment?


Options are :

  • An HTTP_ECV monitor with the attribute parameter
  • An HTTP monitor with the attribute parameter
  • An HTTP_ECV monitor with the customHeaders parameter (Correct)
  • An HTTP monitor with the customHeaders parameter (Correct)

Answer : An HTTP_ECV monitor with the customHeaders parameter An HTTP monitor with the customHeaders parameter

Scenario: A finance company has a site for tax information and tax services. During the tax season, the site gets much more traffic than usual and the week before taxes are due, the site gets more requests than it can handle. When configuring load balancing on the NetScaler for this site, which advanced virtual server option could an administrator configure to prevent the virtual server from going down?


Options are :

  • Max Client
  • Redirect URL
  • Connection-based Spillover (Correct)
  • Backup vservers

Answer : Connection-based Spillover

Citrix 1Y0-992 Meta Frame Presentation Server Feature Exam Set 2

Scenario: A consultant is in charge of a new NelScaler 8.0 deployment at a large customer site. The customer gave the consultant the following information and IP addresses to use when configuring the NetScaler system: Internal Citrix Presentation Server 4.0 IP address: 10.165.30.12 IP addresses to use when configuring the NetScaler 8.0 deployment MIP - 10.165.30.45 NSIP - 10.165.30.60 VIP - 12.15.30.62 DNS Server - 78.35.14.99 When configuring the NetScaler system for this scenario, which IP address will be used by the NetScaler to communicate with the server running Citrix Presentation Server?


Options are :

  • 78.35.14.99
  • 10.165.30.12
  • 10.165.30.45 (Correct)
  • 12.15.30.62
  • 10.165.30.60

Answer : 10.165.30.45

Which method should be used to load balance Intrusion Detection System servers for optimal distribution?


Options are :

  • Source IP Hash
  • Domain Hash
  • URL Hash
  • Destination IP Hash
  • Source IP/Destination IP Hash (Correct)

Answer : Source IP/Destination IP Hash

Scenario: An administrator needs to configure a health check for the web servers of a bank so that the probe fails if the monitor does not receive a 200 code HTTP response for an encrypted HTTP request. How should the administrator configure the health check in the configuration utility to meet this requirement?


Options are :

  • Add an HTTP monitor, select the secure parameter and type in the appropriate HTTP request. (Correct)
  • Add an HTTP-ECV monitor, select the secure parameter, type in the appropriate send string and delete the receive string.
  • Add an HTTPs monitor, type in the appropriate HTTPs request and delete the response code.
  • Add an HTTPs-ECV monitor, type in the appropriate HTTPs send string and delete the receive string.

Answer : Add an HTTP monitor, select the secure parameter and type in the appropriate HTTP request.

Citrix 1Y0-992 Meta Frame Presentation Server Feature Exam Set 4

Scenario: A company based in Beijing was unable to reach their data center for more than a week due to a nearby earthquake. The company now has Distributed Data Centers in multiple regions, including a disaster recovery center, to increase redundancy. The company wants their new NetScaler systems to load balance these centers. Which NetScaler feature will allow load balancing across these centers only for redundancy?


Options are :

  • TCP-based content switching to make a decision between the load balance virtual servers
  • Global Server Load Balancing to make load balancing decisions between the two sites (Correct)
  • Proximity-based Global Server Load Balancing based on the RTT of client requests to virtual servers
  • SNMP load monitor bound to each location and bound to the default NetScaler metric table and with the appropriate SNMP OlDs to load balance the different locations

Answer : Global Server Load Balancing to make load balancing decisions between the two sites

Which method can an administrator configure to load balance cache servers?


Options are :

  • Destination IP Hash
  • URL Hash (Correct)
  • Domain Hash
  • Source IP/Destination IP Hash

Answer : URL Hash

Scenario: An administrator needs to configure a health check for the bank web servers so that the probe fails if the monitor does not receive the expected HTTP data response for an encrypted HTTP request. How should the administrator configure the health check in the configuration utility to meet this requirement?


Options are :

  • Add an HTTP-ECV monitor, select the secure parameter and type in the appropriate send and receive string. (Correct)
  • Add an HTTPs monitor and type in the appropriate HTTPs request and response.
  • Add an HTTP monitor, select the secure parameter and type in the appropriate HTTP request and response.
  • Add an HTTPS-ECV monitor and type in the appropriate send and receive string.

Answer : Add an HTTP-ECV monitor, select the secure parameter and type in the appropriate send and receive string.

Citrix 1Y0-614 Access Suite 4.0 Design Practice Exam Set 2

Scenario: An events ticketing company plans to use the content switching feature of NetScalerto parse traffic so that users purchasing tickets or answering surveys go to group A servers, users accessing images go to either group B or C servers depending on the category and all other traffic goes to group D. All servers are in the same web farm. Which two actions must an administrator perform to correctly define the content switching virtual server so that traffic not going to groups A. C gets directed to group D?


Options are :

  • Bind a load balancing virtual server to the appropriate service for the farm.
  • Bind the appropriate load balancing virtual server to the content switching virtual server with the appropriate policy for content group D.
  • Bind the appropriate load balancing virtual server to the content switching virtual server without a policy. (Correct)
  • Bind the appropriate service to a load balancing virtual server for serving content group D. (Correct)

Answer : Bind the appropriate load balancing virtual server to the content switching virtual server without a policy. Bind the appropriate service to a load balancing virtual server for serving content group D.

Scenario: A consultant is in charge of a new NetScaler8.0 deployment at a large customer site. The customer gave the consultant the following information and IP addresses to use when configuring the NetScaler system: Internal Citrix Presentation Server 4.0 IP address: 192.168.100.12 IP addresses to use when configuring the NetScaler 8.0 deployment NSIP: 10.165.30.45 MIP: 10.165.30.60 VIP: 12.15.30.62 When configuring the NetScaler system for this scenario, which two configuration options could an administrator specify on the NetScaler system to communicate with the server running Citrix Presentation Server?


Options are :

  • Intranet IP in the 192.168.100.X subnet
  • Subnet IP in the 192.168.100.X subnet (Correct)
  • Virtual Server in the 192.168.100.X subnet
  • Static Route to the 192.168.100.X subnet (Correct)

Answer : Subnet IP in the 192.168.100.X subnet Static Route to the 192.168.100.X subnet

Scenario: An administrator is planning to deploy NetScaler systems in an environment with multiple IP subnets, one of which is non-routable. The company is an online retailer and needs outbound connections from the non-routable subnet in order to verify credit cards. What will an administrator need to configure to meet the company's requirements?


Options are :

  • USIP
  • Layer 2 mode
  • SIP
  • USNIP
  • RNAT (Correct)

Answer : RNAT

1Y0-311 Citrix XenApp and XenDesktop 7.15 LTSR Advanced Exam Set 5

An administrator for a bank's network plans to configure an SSL virtual server for HTTP content switching in an environment that requires enD. to-end encryption. Which type of virtual server should the administrator configure?


Options are :

  • Front-end SSL_TCP, Back-end SSL TCP
  • Front-end SSL, Back-end SSL (Correct)
  • Front-end SSL, Back-end HTTP
  • Front-end TCP, Back-end SSL TCP

Answer : Front-end SSL, Back-end SSL

Which command must an administrator use to assign a mapped IP address on a NetScaler system from the command line interface?


Options are :

  • add ns ip -type mip (Correct)
  • set ns ip type mappedIP
  • add ip -mip
  • set ns ip -type mip

Answer : add ns ip -type mip

An administrator plans to configure a NetScaler system to resolve DNS queries using an external DNS server with an IP address of 10.10.10.1. Which command could the administrator use to configure this?


Options are :

  • add nameserver DNS1 10.10.10.1 (Correct)
  • add server DNS1 10.10.10.1 -external
  • add lb vserver DNS1 dns 10.10.10.1
  • add nameserver DNS1 dns 10.10.10.1 -local

Answer : add nameserver DNS1 10.10.10.1

Citrix 1Y0-731 Netscaler 8.0 Administration Practice Exam Set 2

Scenario: A company is setting up new NetScaler systems in High Availability (HA) mode using inline mode. The administrator has connected four interfaces per box and two pairs per box have inline mode configured. The administrator set up each pair with link aggregation because throughput performance is critical. Which option is critical to ensure that the minimum bandwidth is available for link aggregation?


Options are :

  • The throughput option is enabled on the link aggregation channel. (Correct)
  • Monitoring is enabled on link aggregation channel.
  • The physical interface has HA monitor enabled.
  • Failover interface sets (fis) are defined.

Answer : The throughput option is enabled on the link aggregation channel.

Scenario: A company has passed a new policy requiring redundancy in the load balancing of the servers given the criticality of their online store. The administrator is configuring NetScalers for High Availability (HA) in inline mode through the command line interface. The administrator wants the primary NetScaler to have the NSIP address 172.16.200.66 and the secondary NetScalerto have the NSIP address 172.16.200.65. Which two command line interface commands must the administrator use to configure HA in this environment?


Options are :

  • add node 0 172.16.200.65 on primary
  • add node 0 172.16.200.66 on secondary
  • add node 1 172.16.200.65 on primary (Correct)
  • add node 2 172.16.200.66 on secondary (Correct)

Answer : add node 1 172.16.200.65 on primary add node 2 172.16.200.66 on secondary

Scenario: An administrator introduced two new servers into a server farm that can handle more traffic than the older servers. The current load balancing method set for the virtual server managing the traffic for this group of servers is Least Connections. The administrator wants to maintain the load balancing method but also wants to use the new servers to improve performance by having them take more of the traffic than the older servers. Which advanced option must the administrator configure to achieve this?


Options are :

  • Backup vserver
  • Max Client
  • Service Weights (Correct)
  • Spillover
  • Global Setting Override

Answer : Service Weights

1Y0-309 Citrix Access Gateway 8.0 Enterprise Edition Test Set 3

An administrator is configuring a virtual server for clear text TCP traffic from clients that needs to be encrypted prior to being forwarded to the back-end servers across a public network. Which type of virtual server and service should the administrator configure?


Options are :

  • Front-end SSL_TCP, Back-end TCP
  • Front-end TCP, Back-end SSL_TCP
  • Front-end SSL_TCP, Back-end SSL_TCP (Correct)
  • Front-end SSL, Back-end SSL

Answer : Front-end SSL_TCP, Back-end SSL_TCP

Scenario: An administrator configured the advanced options for a service; however, since doing so, the service keeps going DOWN because it is receiving too much traffic. Which advanced option did the administrator misconfigure and how should the administrator configure it?


Options are :

  • The administrator set the Max Client to 5 and should set it to 60
  • The administrator set the Max Request to 5 and should set it to 50
  • The administrator set the Max Client to 0 and should set it to 50 (Correct)
  • The administrator set the Max Request to 0 and should set it to 60

Answer : The administrator set the Max Client to 0 and should set it to 50

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions