Citrix 1Y0-351 NetScaler 10.5 Essentials and Networking Exam Set 6

Scenario: A network engineer needs to add an NTP server to a NetScaler appliance. The NTP service is configured on 10.10.1.49. Which command should the network engineer use within the command-line interface to add in an NTP server for time synchronization?


Options are :

  • add ntp server 10.10.1.49
  • add server NTP 10.10.1.49
  • add service NTP 10.10.1.49 UDP 123
  • add service NTP 10.10.1.49 TCP 123

Answer : add ntp server 10.10.1.49

Scenario: An engineer configures two NetScaler appliances in a high availability (HA) pair. As part of a monthly health check, the engineer attempts to log on to the second node of the HA pair and is unable to access the management IP Address. The engineer logs on to the first NetScaler node and verifies that HA is working and operational. What does the engineer need to do to resolve this problem?


Options are :

  • Create an ACL to allow access to the NSIP of the second node.
  • Add a SNIP for the Management IP Address of the second node.
  • Ensure that HA Route Monitors have been configured for the second node.
  • Change the NSRoot password back to default then log on to the second node.

Answer : Create an ACL to allow access to the NSIP of the second node.

Scenario: An engineer needs to configure a monitor to ensure that each server is tested every 10 seconds and requires that the server pass the test four consecutive times before marking a server as UP. If the test fails, the server should be marked as down for 60 seconds. To configure the monitor, the engineer should configure an interval of 10 seconds, down-time of 60 seconds; __________ as 4; and retries as __________. (Choose the correct set of options to complete the sentence.)


Options are :

  • failure retries; 4
  • failure retries; 1
  • success retries; 4
  • success retries; 1

Answer : success retries; 1

Citrix 1Y0-351 NetScaler 10.5 Essentials and Networking Exam Set 7

How could an engineer configure a monitor to ensure that a server is marked as DOWN if the monitor test is successful?


Options are :

  • Enable the LRTM option for the monitor
  • Disable the Health monitoring option for the service group
  • Disable Down state flush for the service group
  • Enable the Reverse option for the monitor

Answer : Enable the Reverse option for the monitor

Which step is required to ensure that SSL traffic is passed through the NetScaler to backend services without processing SSL on the NetScaler appliance?


Options are :

  • Bind an SSL certificate to a service group.
  • Bind an SSL certificate to the virtual server
  • Create a service group of type SSL_BRIDGE.
  • Create a service group of type HTTP.
  • Create a service group of type SSL.

Answer : Create a service group of type SSL_BRIDGE.

Scenario: A security test has shown that the NetScaler is forwarding IP packets. Company standard operating procedure is that the routers should be the only devices forwarding packets. Which step should the network engineer take to prevent forwarding packets?


Options are :

  • Enable Layer 2 mode.
  • Disable Layer 3 mode.
  • Disable Path MTU Discovery.
  • Enable MAC based forwarding.

Answer : Disable Layer 3 mode.

1Y0-200 Managing Citrix XenDesktop 7 Solutions Exam Set 1

Scenario: A network engineer has bound a service group containing four web servers to a virtual server. The virtual server is UP but users report that they are unable to access the virtual server. In order to troubleshoot this issue, the engineer should use telnet from __________. (Choose the correct option to complete the sentence.)


Options are :

  • a PC to the mapped IP address
  • the NetScaler shell to one of the web servers
  • a PC to the virtual IP address
  • a PC to the subnet IP address

Answer : a PC to the virtual IP address

Scenario: A NetScaler high availability (HA) pair has the following interfaces connected: 1/1 - Test network 1/2 - Production network The network engineer needs to re-cable the test network and wants to ensure that, when the cable is removed, HA fail over does NOT occur unless the production network also goes down. Which step should the engineer take to meet these requirements?


Options are :

  • Configure LACP for interface 1/1.
  • Bind interfaces 1/1 and 1/2 into a channel, then disable HA monitoring.
  • Set the throughput to 0 for interface 1/1.
  • Disable HA monitoring on interface 1/1.

Answer : Disable HA monitoring on interface 1/1.

Scenario: A NetScaler engineer is on the phone with Technical Support to troubleshoot an issue. The NetScaler engineer generated a support archive and needs to send the file to the Technical Support Specialist to help resolve the problem with the appliance. In which directory could the engineer retrieve the information?


Options are :

  • /nsconfig
  • /var/crash
  • /var/tmp/support
  • /var/nstrace

Answer : /var/tmp/support

1Y0-200 Managing Citrix XenDesktop 7 Solutions Exam Set 2

Scenario: A network engineer has created two selectors to use to populate a cache group in integrated caching. One selector, "Hit," will determine what to add to the group. The other, "Inval", will select what should be invalidated. Which command should the engineer run to create the cache group?


Options are :

  • add cache contentgroup CacheGroup1 -hitSelector Hit -invalSelector Inval
  • add cache contentgroup CacheGroup1 -hitParams Hit -invalParam Inval
  • set cache contentgroup CacheGroup1 -hitSelector Hit - invalSelector Inval -type HTTP
  • set cache contentgroup CacheGroup1 - hitParams Hit -invalParam Inval -type HTTP

Answer : add cache contentgroup CacheGroup1 -hitSelector Hit -invalSelector Inval

A network engineer should use the Advanced tab when configuring load balancing to enable __________. (Choose the correct option to answer the question.)


Options are :

  • Direct Server Return Mode
  • Integrated caching
  • SSL offloading
  • EdgeSight Monitoring

Answer : Direct Server Return Mode

Scenario: An engineer implementing a NetScaler is tasked with creating a new VLAN, named VLAN 2, and adding it to the current interfaces. A new IP address of 10.102.29.54 with a network mask of 255.255.255.0 must be configured for VLAN 2. Which commands could the engineer use to achieve this configuration in the command-line interface prior to binding VLAN 2?


Options are :

  • set vlan 2 -aliasName VLAN2 add ns ip 10.102.29.54 255.255.255.0
  • add ns ip 10.102.29.54 255.255.255.0 add vlan 2
  • add ns ip 10.102.29.54 255.255.255.0 -vrID 2
  • add ns ip 10.102.29.54 255.255.255.0 -type SNIP set ns ip 10.102.29.54 255.255.255.0 -vrID 2

Answer : add ns ip 10.102.29.54 255.255.255.0 add vlan 2

1Y0-200 Managing Citrix XenDesktop 7 Solutions Exam Set 3

A public SSL certificate on a virtual server is about to expire and the NetScaler engineer needs to renew the certificate before it expires. Which step must the engineer take to renew the SSL Certificate?


Options are :

  • Generate a new CSR
  • Recreate the Private Keys
  • Update the existing certificate
  • Execute CRL Management

Answer : Update the existing certificate

Scenario: A NetScaler environment uses two-factor authentication and the second authentication method is AD. A user logs in to the environment but does NOT receive access to the resources that the user should have access to. How can an engineer determine the AD authentication issue on the NetScaler?


Options are :

  • Check NSlogs
  • Check the authorization configuration
  • Use nsconmsg
  • Use the cat aaad.debug command

Answer : Use the cat aaad.debug command

Scenario: A network engineer has installed a NetScaler system into their corporate DMZ and would like to provide access to a web server on the internal LAN. The web server will be accessed by external users through the NetScaler. The firewall administrator has opened the relevant ports required on the external and the internal firewall. The engineer notices that the virtual server and services representing the web server are down and the internal web server does NOT appear accessible from the NetScaler. What could be the cause of this?


Options are :

  • Client IP Insertion is not enabled.
  • USIP is not enabled.
  • A URL rewrite policy is not created.
  • A SNIP address has not been added.

Answer : A SNIP address has not been added.

1Y0-200 Managing Citrix XenDesktop 7 Solutions Practice Exam Set 1

How could a network engineer gather detailed network information?


Options are :

  • System node -> Diagnostics -> Start new trace
  • System node -> Diagnostics -> Show techsupport
  • System node -> Diagnostics -> Call home
  • System node -> Diagnostics -> Show running vs saved config

Answer : System node -> Diagnostics -> Start new trace

Scenario: A virtual server named New_Server has been disabled to perform an emergency upgrade; however requests from clients are NOT being redirected to the maintenance page. The redirected URL configuration is: >set cs vserver Website_main -lbvserver New_Server -backupVserver Backup_Server - redirectURL http://www.mydomain.com/maintenance - soMethod Connection -soThreshold 1000 - soPersistence enabled Why are requests from clients NOT being redirected to the maintenance page?


Options are :

  • The spillover persistence has been activated.
  • The backup virtual server takes precedence over the redirect URL.
  • It has not been linked to content switching policies.
  • The backup virtual server is unavailable.

Answer : The backup virtual server takes precedence over the redirect URL.

What type of protocol does AppFlow use for reporting?


Options are :

  • UDP
  • HTTP
  • SSL_TCP
  • TCP

Answer : UDP

1Y0-200 Managing Citrix XenDesktop 7 Solutions Practice Exam Set 2

Scenario: A network engineer has configured GSLB for a multisite environment. All GSLB services show as UP with an UP MEP status. The engineer has observed that DNS queries are directed to the SNIP of the NetScaler; however, no DNS response is being received. How can the engineer resolve this issue?


Options are :

  • Create a load balancing virtual server for DNS.
  • Select the "Send all "active" service IPs' in response (MIR)" option.
  • Add an ADNS service on the SNIP.
  • Change the DNS delegation to the NSIP.

Answer : Add an ADNS service on the SNIP.

Scenario: A network engineer has configured an HTTP application to be load balanced using a virtual server named Svr1. Users have reported intermittent errors and the engineer has been given the client IP address of an affected user and asked to determine which back end service they are connected to. Using the command-line interface, how could the engineer find this information?


Options are :

  • Show lb vServer Svr1 -Summary
  • Show lb persistentSessions Svr1
  • Show system session
  • Show lb vServer Svr1

Answer : Show lb persistentSessions Svr1

Scenario: Primary NetScaler (NS1) is licensed for 10000 Maximum ICA users and 305 Access Gateway users. Secondary NetScaler (NS2) is licensed for 10000 Maximum ICA users and five Access Gateway users. From where and which command should a network engineer run to display diagnostics on the licenses?


Options are :

  • From the command-line interface, run 'cat /var/log/license.log'.
  • From the shell, run 'more /var/log/license.log'.
  • From the shell, run 'view license'.
  • From the command-line interface, run 'show license'.

Answer : From the shell, run 'more /var/log/license.log'.

1Y0-200 Managing Citrix XenDesktop 7 Solutions Practice Exam Set 3

A network engineer is troubleshooting a situation where ARP requests for IPs in other subnets (for example 10.192.12.80) are appearing in the 10.192.8.0/24 subnet. Which command could the engineer run on the NetScaler to verify IP to VLAN bindings?


Options are :

  • show arp
  • show vlan
  • show ip
  • netstat -r

Answer : show vlan

Scenario: A network engineer has modified the configuration of a content-switching virtual server, Website_main, because a second content-switching server that is capable of handling more connections has been added to the NetScaler implementation. Both servers will remain in operation. The engineer made the following configuration changes: >set cs vserver Website_main -lbvserver New_Server -backupVserver Old_Server -redirectURL http://www.mydomain.com/maintenance -soMethod Connection -soThreshold 1000 Why did the engineer enable the spillover option?


Options are :

  • To handle incoming connections while the server reaches its limit of connections
  • To handle the extra connections using the old server without dropping them
  • To handle incoming connections in case the new server is unavailable
  • To redirect the extra connections to the Maintenance website when it is needed

Answer : To handle the extra connections using the old server without dropping them

Scenario: Company Inc. wants to tag incoming requests with a header that indicates which browser is being used on the connection. This helps the server keep track of the browsers after the NetScaler has delivered the connections to the back end. The engineer should create __________ actions to __________.


Options are :

  • rewrite; insert tags on the server response
  • responder; filter the browser type on the client header
  • rewrite; insert tags on the client header
  • responder; separate the client requests

Answer : rewrite; insert tags on the client header

1Y0-200 Managing Citrix XenDesktop 7 Solutions Practice Exam Set 4

Scenario: A network engineer gets an error message when using the configuration utility to import a PKCS#12 certificate that contains a dollar sign ($), a backquote (`), or an escape (\) character password. In order to address this error, the network engineer could prefix it with __________. (Choose the correct option to complete the sentence.)


Options are :

  • a backquote character (`)
  • a dollar sign character ($)
  • a double quotation character (")
  • an escape character (\)

Answer : an escape character (\)

An environment network has: - High bandwidth - Low packet loss - High Round-Trip Time (RTT) Which TCP profile should an engineer configure for the environment described?


Options are :

  • Nstcp_default_profile
  • Nstcp_default_tcp_lan
  • Nstcp_default_tcp_lfp
  • Nstcp_default_tcp_lnp

Answer : Nstcp_default_tcp_lfp

Scenario: A network engineer needs to provide web server administrators with access to monitoring and reporting after changing the default root password during the initial setup of the NetScaler. The engineer needs to ensure that the web server administrators can perform this task. What should the engineer do in order to ensure that the administrators are able to log on to the NetScaler?


Options are :

  • Create user accounts.
  • Create a group.
  • Create an authorization policy.
  • Create an authentication policy.

Answer : Create user accounts.

1Y0-200 Managing Citrix XenDesktop 7 Solutions Practice Test Set 1

An engineer has bound a policy to a test virtual server. How could the engineer verify that the policy is being applied?


Options are :

  • Enable the AppFlow logging option for the virtual server.
  • Monitor the number of hits for the virtual server.
  • Ensure the policy has a greater priority value than other policies bound to the test virtual server.
  • Monitor the number of hits for the policy.

Answer : Monitor the number of hits for the policy.

Scenario: GSLB has been configured for use within a multisite environment. The MEP status is reported as down on all GSLB appliances. The appliances have been configured for unsecured MEP exchange. Which port must the network engineer ensure is open between the NetScaler appliances?


Options are :

  • UDP 3012
  • TCP 3012
  • TCP 3011
  • UDP 3011

Answer : TCP 3011

The disk is full on a NetScaler appliance but NO alerts were generated by the SNMP traps. What is the likely cause of this failed alert?


Options are :

  • Auditing is not enabled.
  • EdgeSight monitoring is not configured.
  • The threshold was not set for the alarm.
  • Health monitoring has not been enabled.

Answer : The threshold was not set for the alarm.

1Y0-200 Managing Citrix XenDesktop 7 Solutions Practice Test Set 2

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions