ICND2 200-105 Certification Practice Tests Set 1

What is the default VLAN on an access port?


Options are :

  • 1024
  • 10
  • 0
  • 1

Answer :1

400-101 CCIE Routing and Switching Written Practice Exam Set 7

Which two components are used to identify a neighbor in a BGP configuration? (Choose two).


Options are :

  • autonomous system number
  • version number
  • router ID
  • subnet mask
  • IP address

Answer :autonomous system number IP address

Which two circumstances can cause collision domain issues on VLAN domain? (Choose two).


Options are :

  • Duplex mismatches on Ethernet segments in the same VLAN
  • A failing NIC in an end device
  • An overloaded shared segment
  • Multiple errors on switchport interfaces
  • Congestion on the switch inband path

Answer :Multiple errors on switchport interfaces

Which three statements are typical characteristics of VLAN arrangement? (Choose three).


Options are :

  • A new switch has no VLANs configured.
  • VLANs cannot span multiple switches.
  • Each VLAN uses a separate address space.
  • Connectivity between VLANs requires a Layer 3 device.
  • VLANs typically decrease the number of collision domains.
  • A switch maintains a separate bridging table for each VLAN.

Answer :Each VLAN uses a separate address space. Connectivity between VLANs requires a Layer 3 device. A switch maintains a separate bridging table for each VLAN.

210-260 Implementing Cisco Network Security Practice Exam Set 6

Which spanning-tree feature places a port immediately into a forwarding state?


Options are :

  • BPDU guard
  • Uplink Fast
  • loop guard
  • PortFast
  • UDLD

Answer :PortFast

While you were troubleshooting a connection issue, a ping from one VLAN to another VLAN on the same switch failed. Which command verifies that IP routing is enabled on interfaces and the local VLANs are up?


Options are :

  • show ip route
  • show ip statistics
  • show ip nat statistics
  • show ip interface brief

Answer :show ip interface brief

Which two conditions can be used to elect the spanning-tree root bridge? (Choose two).


Options are :

  • The lowest system ID
  • The lowest switch priority
  • The highest port priority
  • The lowest MAC address
  • The highest MAC address

Answer :The lowest switch priority The lowest MAC address

200-125 Cisco Certified Network Associate (CCNA) Exam Set 1

What are two characteristics of a switch that is configured as a VTP client? (Choose two).


Options are :

  • VTP advertisements are not forwarded to neighboring switches that are configured in VTP transparent mode.
  • VTP client is the default VTP mode.
  • When switches in VTP client mode are rebooted, they send a VTP advertisement request to the VTP servers.
  • On switches that are configured to operate in client mode, VLANs can be created, deleted, or renamed locally.
  • The local VLAN configuration is updated only when an update that has a higher configuration revision number is received.
  • If a switch that is configured to operate in client mode cannot access a VTP server, then the switch reverts to transparent mode.

Answer :When switches in VTP client mode are rebooted, they send a VTP advertisement request to the VTP servers. The local VLAN configuration is updated only when an update that has a higher configuration revision number is received.

Which parameter or parameters are used to calculate OSPF cost in Cisco Routers?


Options are :

  • Bandwidth, MTU, Reliability, Delay, and Load
  • Bandwidth and Delay
  • Bandwidth, Delay, and MTU
  • Bandwidth

Answer :Bandwidth

Which protocol provides a method of sharing VLAN configuration information between two Cisco switches?


Options are :

  • 802.1Q
  • VTP
  • STP
  • RSTP

Answer :VTP

300-320 Designing Cisco Network Service Architectures Exam Set 5

What can be done to secure the virtual terminal interfaces on a router? (Choose two).


Options are :

  • Physically secure the interface.
  • Enter an access list and apply it to the virtual terminal interfaces using the access-class command.
  • Administratively shut down the interface.
  • Configure a virtual terminal password and login process.
  • Create an access list and apply it to the virtual terminal interfaces with the access-group command.

Answer :Enter an access list and apply it to the virtual terminal interfaces using the access-class command. Configure a virtual terminal password and login process.

Which option is a benefit of switch stacking?


Options are :

  • It provides higher port density with better resource usage.
  • It supports better performance of high-needs applications.
  • It simplifies adding and removing hosts.
  • It provides redundancy with no impact on resource usage.

Answer :It provides higher port density with better resource usage.

Which identification number is valid for an extended ACL?


Options are :

  • 299
  • 99
  • 1
  • 1099
  • 100
  • 64

Answer :100

210-065 Implementing Cisco Video Network Devices Exam Set 1

Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two).


Options are :

  • All OSPF routers in an area must have the same process ID.
  • Only one process number can be used on the same router.
  • Different process identifier can be used to run multiple OSPF processes
  • The process number can be any number from 1 to 65,535.
  • Hello packets are sent to each neighbor to determine the processor identifier.

Answer :Different process identifier can be used to run multiple OSPF processes The process number can be any number from 1 to 65,535.

Which process is associated with spanning-tree convergence?


Options are :

  • Assigning the port ID
  • Selecting designated ports
  • Determining the path cost
  • Learning the sender bridge ID

Answer :Selecting designated ports

Which EIGRP for IPv6 command can you enter to view the link-local addressee of the neighbors of a device?


Options are :

  • show ipv6 eigrp neighbors
  • show ip eigrp traffic
  • show ipv6 eigrp 20 interfaces
  • show ipv6 route eigrp

Answer :show ipv6 eigrp neighbors

300-320 Designing Cisco Network Service Architectures Exam Set 1

Which statement about the IP SLAs ICMP Echo operation is true?


Options are :

  • It is used to identify the beet source interface from which to send traffic.
  • The frequency of the operations specified in milliseconds.
  • It is used to determine the frequency of ICMP packets.
  • It is configured in enable mode.

Answer :It is used to determine the frequency of ICMP packets.

Which two pieces of information are provided by the show controllers serial 0 command? (Choose two).


Options are :

  • The uptime of the interface
  • The full configuration of the interface
  • The interface's duplex settings
  • The type of cable that is connected to the interface.
  • The status of the physical layer of the interface

Answer :The type of cable that is connected to the interface. The status of the physical layer of the interface

Which protocol supports sharing the VLAN configuration between two or more switches?


Options are :

  • STP
  • VTP
  • multicast
  • split-horizon

Answer :VTP

210-260 Implementing Cisco Network Security Practice Exam Set 5

Router(config)# router eigrp 1. What is the significance of the "1" in this configuration?


Options are :

  • It is the AS number for EIGRP and must be the same on all EIGRP routers.
  • It is the process ID for EIGRP and is locally significant to this router.
  • It is the AS number for EIGRP and is locally significant to this router.
  • It is the process ID for EIGRP and must be the same on all EIGRP routers.

Answer :It is the AS number for EIGRP and must be the same on all EIGRP routers.

Which statements are true about EIGRP successor routes? (Choose two).


Options are :

  • Successor routes are fagged as 'Active' in the routing table.
  • A successor route is used by EIGRP to forward traffic to a destination.
  • Successor routes are stored in the neighbor table following the discovery process.
  • Successor routes are saved in the topology table to be used if the primary route fails.
  • A successor route may be backed up by a feasible successor route.

Answer :A successor route is used by EIGRP to forward traffic to a destination. A successor route may be backed up by a feasible successor route.

Which three statements about RSTP are true? (Choose three).


Options are :

  • RSTP also uses the STP proposal-agreement sequence.
  • RSTP expands the STP port roles by adding the alternate and backup roles.
  • RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
  • RSTP uses the same timer-based process as STP on point-to-point links.
  • RSTP significantly reduce topology re-converging time after a link failure.
  • RSTP port states are blocking, discarding, learning, or forwarding.

Answer :RSTP expands the STP port roles by adding the alternate and backup roles. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does. RSTP significantly reduce topology re-converging time after a link failure.

210-065 Implementing Cisco Video Network Devices Exam Set 6

Which statement about switch access ports is true?


Options are :

  • They drop packets with 802.1Q tags.
  • They can receive traffic from more than one VLAN with no voice support.
  • A VLAN must be assigned to an access port before it is created.
  • By default, they carry traffic for VLAN 10.

Answer :They drop packets with 802.1Q tags.

Which type of topology is required by DMVPN?


Options are :

  • ring
  • partial mesh
  • hub-and-spoke
  • full mesh

Answer :hub-and-spoke

At which layer of the OSI model is RSTP used to prevent loops?


Options are :

  • Network
  • Physical
  • Data link
  • Transport

Answer :Data link

400-101 CCIE Routing and Switching Written Practice Exam Set 6

What is the default maximum number of equal-cost path that can be placed into the routing table of a Cisco OSPF router?


Options are :

  • 4
  • 2
  • unlimited
  • 16

Answer :4

What is the first step you perform to configure an SNMPv3 user?


Options are :

  • Configure the remote engine ID.
  • Configure the server group.
  • Configure server traps.
  • Configure the server host.

Answer :Configure the server group.

If host Z needs to send data through router R1 to a storage server, which destination MAC address does host Z use to transmit packets?


Options are :

  • The host Z MAC address
  • The MAC address of the interface on R1 that connects to the storage server
  • The MAC address of the storage server interface
  • The MAC address of the interface on R1 that connects to host Z

Answer :The MAC address of the interface on R1 that connects to host Z

200-105 Inter connecting Cisco Networking Devices Exam Set 2

Which version of SNMP first allowed user-based access?


Options are :

  • SNMPv3
  • SNMPv1
  • SNMPv2
  • SNMPv3 with RBAC

Answer :SNMPv3

Which statement about QoS default behavior is true?


Options are :

  • VoIP traffic is passed without being tagged.
  • Packets that arrive with a tag are untagged at the edge of an administrative domain.
  • Packets are classified internally with an environment.
  • Video traffic is passed with a well-known DSCP value of 46.
  • Ports are untrusted by default.

Answer :Packets that arrive with a tag are untagged at the edge of an administrative domain.

Which statement about DTP is true?


Options are :

  • It sends data on VLAN 1.
  • It negotiates a trunk link after VTP has been configured.
  • It uses desirable mode by default.
  • It uses the native VLAN.

Answer :It sends data on VLAN 1.

400-101 CCIE Routing and Switching Written Practice Exam Set 10

Which statement about MPLS is true?


Options are :

  • It operates between Layer 2 and Layer 3.
  • It operates in Layer 1.
  • it operates in Layer 2.
  • It operates in Layer 3.

Answer :It operates between Layer 2 and Layer 3.

Which two states are the port states when RSTP has converged? (Choose two).


Options are :

  • discarding
  • disabled
  • learning
  • forwarding
  • listening

Answer :discarding forwarding

Which IEEE standard does PVST+ use to tunnel information?


Options are :

  • 802.1x
  • 802.1w
  • 802.1e
  • 802 1q

Answer :802 1q

100-105 Net Cert Interconnecting Cisco Networking Exam Set 6

Which statement about slow inter VLAN forwarding is true?


Options are :

  • The VLANs are experiencing slowness because multiple devices are connected to the same hub.
  • The VLANs are experiencing slowness due to a duplex mismatch.
  • The entire VLAN is experiencing slowness.
  • The VLAN is experiencing slowness in the point-to-point collisions connection.
  • The local VLAN is working normally, but traffic to the alternate VLAN is forwarded slower than expected.

Answer :The VLANs are experiencing slowness due to a duplex mismatch.

Which option describes how a switch in rapid PVST+ mode responds to a topology change?


Options are :

  • It sets a timer to delete dynamic MAC addressee that were learned by all ports on the switch.
  • It immediately deletes all MAC addressee that were learned dynamically by ports in the same STP instance.
  • It immediately deletes dynamic MAC addressee that were learned by all ports on the switch.
  • It deletes a timer to delete all MAC addressee that were learned dynamically by ports in the same STP instance.

Answer :It immediately deletes all MAC addressee that were learned dynamically by ports in the same STP instance.

Which three options are the HSRP states for a router? (Choose three).


Options are :

  • primary
  • speak
  • secondary
  • learn
  • listen
  • initialize

Answer :speak learn listen

Cisco CCNP Route 300-101 Practice Tests Set 2

Which protocol authenticates connected devices before allowing them to access the LAN?


Options are :

  • 802.1d
  • 802.11
  • 802.1x
  • 802.1w

Answer :802.1x

Which statement about named ACLs is true?


Options are :

  • They are used to filter Layer 7 traffic.
  • They are used to rate limit traffic destined to targeted networks.
  • They are used to filter usernames and passwords for Telnet and SSH.
  • They support standard ACLs only.
  • They support standard and extended ACLs.

Answer :They support standard and extended ACLs.

What are three characteristics of the OSPF routing protocol? (Choose three).


Options are :

  • It converges quickly.
  • OSPF routers send the complete routing table to all directly attached Router E.
  • It uses cost to determine the best route.
  • It uses the DUAL algorithm to determine the best route.
  • OSPF routers discover neighbors before exchanging routing information.
  • OSPF is a classful routing protocol.

Answer :It converges quickly. It uses cost to determine the best route. OSPF routers discover neighbors before exchanging routing information.

300-320 Designing Cisco Network Service Architectures Exam Set 1

Which part of the PPPoE server configuration contains the information used to assign an IP address to a PPPoE client?


Options are :

  • dialer interface
  • DHCP
  • AAA authentication
  • virtual-template interface

Answer :dialer interface

Which two of these statements regarding RSTP are correct? (Choose two).


Options are :

  • RSTP cannot operate with PVST+.
  • RSTP is compatible with the original IEEE 802.1D STP.
  • RSTP defines new port roles.
  • RSTP defines no new port states.
  • RSTP is a proprietary implementation of IEEE 802.1D STP.

Answer :RSTP is compatible with the original IEEE 802.1D STP. RSTP defines new port roles.

Which option describes a difference between EIGRP for IPv4 and IPv6?


Options are :

  • Only EIGRP for IPv6 requires a router ID to be configured under the routing process
  • AS numbers are configured in EIGRP but not in EIGRPv3.
  • Only EIGRP for IPv6 is enabled in the global configuration mode.
  • Only EIGRP for IPv6 advertises all connected networks.

Answer :Only EIGRP for IPv6 requires a router ID to be configured under the routing process

Cisco 100-101 Interconnecting Cisco Networking Devices Exam Set 1

What is the best way to verify that a host has a path to other hosts in different networks?


Options are :

  • Ping the remote network.
  • Ping the loopback address.
  • Ping the default gateway.
  • Ping the local interface address.

Answer :Ping the remote network.

Which term describes a spanning-tree network that has all switch ports in either the blocking or forwarding state?


Options are :

  • converged
  • spanned
  • provisioned
  • redundant

Answer :converged

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions