Cisco CCNP Route 300-101 Practice Tests Set 5


Company-A has single-homed connection to ISP-A. From two show commands issued on router Company-A you notice that interface Ethernet 0/0 has been successfully configured with IP address from ISPs DHCP server, and also you notice that Company-A router has received a default route from ISP with Administrative Distance of 254. What name is that static route known as?


Options are :

  • Summary Static route
  • Floating Static route
  • External Static route
  • Standard Static route

Answer :Floating Static route

Cisco 100-101 Interconnecting Cisco Networking Devices Exam Set 4

Access Control Entries (ACEs) are permit or deny statements that together make Access Control List (ACL), intermediary devices can use ACL to permit or deny traffic.

Similar to IPv4 ACL an IPv6 ACL has implicit deny statement at the end of every ACL configured. What two other implicit statement are added by default before implicit deny at the end of every IPv6 ACL configured? (Choose two.)


Options are :

  • Permit icmp any any ra-rs
  • Deny icmp any any nd-ns
  • Permit icmp any any nd-ns
  • Deny icmp any any ra-rs
  • Permit icmp any any rs-ra
  • Deny icmp any any nd-na
  • Deny icmp any any rs-ra
  • Permit icmp any any nd-na

Answer :Permit icmp any any nd-ns Permit icmp any any nd-na


Refer to the exhibit. uRPF verifies that source IP address is reachable by comparing Forwarding Information Base (FIB) that is routable only in loose mode, and on strict mode verifying that packet has reached the router via same interface router will use to get to the source.

Network technician has enabled Loose Mode Unicast Reverse Path Forwarding (uRPF) with the following command:

R1(config)# interface serial 1/0 R1(config-if)# ip verify unicast source reachable-via any

If packet arrives on Serial1/0 interface with source IP address 10.1.1.1, which action will the router take?


Options are :

  • Router CE-1 will drop the packet because the source is not in Forwarding Information Base (FIB)
  • uRPF is not active until UDLD is configured
  • Wrong configuration as Access Control List has to be used with uRPF
  • Router CE-1 will forward the packet because the source is matched with default entry in Forwarding Information Base (FIB)
  • You can not configure uRPF in serial interface, only Ethernet interfaces are capable of uRPF

Answer :Router CE-1 will drop the packet because the source is not in Forwarding Information Base (FIB)

What is the default administrative distance, metric and metric-type for any route redistributed to OSPF protocol?


Options are :

  • Administrative distance = 110, metric=20 with metric-type 2
  • Administrative distance = 170, metric=20 with metric-type 2
  • Administrative distance = 110, metric=infinity with metric-type 2
  • Administrative distance = 110, metric=20 with metric-type 1
  • Administrative distance = 20, metric=1 with metric-type 2
  • Administrative distance = EX 2, metric=20 with metric-type 2

Answer :Administrative distance = 110, metric=20 with metric-type 2

100-105 Net Cert Interconnecting Cisco Networking Exam Set 7


Refer to the exhibit. The system administrator has issued command show ip interface ethernet 0/0. From output displayed in the exhibit, which packet switching method is being used on interface e0/0?


Options are :

  • Flow switching
  • Process switching
  • Fast switching
  • Cisco Express Forwarding (CEF)

Answer :Process switching

Which flag is used for Path Maximum transmission unit (MTU) Discovery (PMTUD)?


Options are :

  • Don’t Fragment
  • Reserved bit
  • More fragments
  • Differentiated Services Codepoint

Answer :Don’t Fragment

When a router loses a route and does not have an FS in its topology table, it looks for an alternative path to the destination - known as going active on a route, and it starts querying the neighbors.

If a neighbor does not have an alternative route, it queries each of its own neighbors for an alternative path.

The queries then propagate through the network, thus creating an expanding tree of queries. Why would EIGRP return a stuck in active (SIA) messages?


Options are :

  • Router is stub router and the state is always stuck in active (SIA)
  • EIGRP Active Enhancement Process is in effect
  • It has not received a reply to a query
  • Automatic network summarization is in effect

Answer :It has not received a reply to a query

What is the new name for LSA Type 3 summary LSA, in OSPFV3?


Options are :

  • Inter-area-prefix-LSA
  • Link LSA
  • Inter-area-router-LSA
  • Intra-area LSA

Answer :Inter-area-prefix-LSA

Cisco Data Center Architecture Set 3

Access control policies specify how access to infrastructure devices should be secured and main goal would be to minimize unauthorized connections. Which are two methods to authenticate users accessing infrastructure devices? (Choose Two.)


Options are :

  • Server-Based Authentication
  • Hybrid Authentication
  • Challenge Handshake Authentication
  • Local Authentication
  • Password Authentication Protocol
  • Kerberos Authentication
  • Key Authentication

Answer :Server-Based Authentication Local Authentication


Refer to the exhibit. Which statement is true regarding Network Time Protocol (NTP) configuration displayed in exhibit?


Options are :

  • Router CE-1 will respond to NTP client requests with IP address 10.1.1.1
  • Command is misconfigured, it should be ntp access-group 1 serve-only
  • Router CE-1 will accept NTP request and updates
  • Router CE-1 will synchronize its time from NTP server with IP address 10.1.1.1 only

Answer :Router CE-1 will respond to NTP client requests with IP address 10.1.1.1

100-105 Net Cert Interconnecting Cisco Networking Exam Set 2

In DHCPv6 communication messages are sent as best effort delivery (UDP). Which two port number will be used in client to server and server to client communication? (Choose two.)


Options are :

  • Client to Server = UDP 546
  • Server to Client = UDP 68
  • Client to Server = UDP 547
  • Client to Server = UDP 67
  • Server to Client = UDP 547
  • Server to Client = UDP 546

Answer :Client to Server = UDP 547 Server to Client = UDP 546

Time/clock synchronization is very important to manage, secure and troubleshoot a network. Which combination of source and destination port numbers will be used on client to server NTP communication?


Options are :

  • Source: UDP port private range anything from 49152 - 65535, Destination UDP port 123
  • Source: UDP port 123, Destination UDP port 123
  • Source: TCP port 123, Destination TCP port 123
  • Source: TCP port private range anything from 49152 - 65535, Destination UDP port 123

Answer :Source: UDP port 123, Destination UDP port 123

EIGRP Hello packets are used to discover & form adjacencies with neighbors and are always sent unreliably. Therefore Hello packets do not require acknowledgment

What is the source and destination address where EIGRP for IPv6 sends hello packets to discover & form adjacencies? (Choose two.)


Options are :

  • source: IPv6 global address
  • source: Solicited-node multicast address
  • source: IPv6 unique-local address
  • destination: ff02::a multicast address
  • destination: IPv6 unique-local address
  • source: IPv6 link-local address
  • destination: IPv6 link-local address
  • destination: IPv6 global address

Answer :destination: ff02::a multicast address source: IPv6 link-local address

200-125 Cisco Certified Network Associate Practice Exam Set 10

Which router-id configuration command is allowed in Cisco IOS OSPF process? (Select all that apply.)


Options are :

  • R1(config-router)#router-id 64512
  • R1(config-router)#router-id 127.0.0.1
  • R1(config-router)#router-id 0.0.0.0
  • R1(config-router)#router-id 255.255.255.255

Answer :R1(config-router)#router-id 127.0.0.1 R1(config-router)#router-id 255.255.255.255

When comparing IPv4 header and IPv6 Header which field is new addition in IPv6 header, not found in IPv4 header?


Options are :

  • Traffic Class
  • Hop Limit
  • Flow Label
  • Next Header
  • Version

Answer :Flow Label


Refer to the exhibit. A network engineer has used show ip sla summary command to view if SLA is operational. Return code is “OK”. What could be tracked from the return code “OK”?


Options are :

  • Availability
  • Operational
  • Scalability
  • State

Answer :State

ICND1 100-105 Certification Practice Tests Set 4

What are OSPF authentication types? (Select all that apply.) 


Options are :

  • Type 3
  • Type 0
  • Type 5
  • Type 6
  • Type 2
  • Type 1
  • Type 4

Answer :Type 0 Type 2 Type 1


Refer to the exhibit. All routers are configured with EIGRP in the topology. Given the sample exhibited metric values, which router will be chosen as Successor and what will be the feasibility distance from R1 to R5 LAN network 10.0.0.0/24?


Options are :

  • Successor R2 with feasibility distance of 25
  • Successor R3 with feasibility distance of 30
  • Successor R4 with feasibility distance of 40
  • Successor R2 with feasibility distance of 30
  • Successor R5 with feasibility distance of 5
  • Successor R3 with feasibility distance of 35
  • Successor R4 with feasibility distance of 45

Answer :Successor R2 with feasibility distance of 30

Simple Network Management Protocol (SNMP) is internet standard application layer protocol developed to allow system administrators to monitor and manage network infrastructure devices. Which combination of protocol and port number does SNMP use for transport?


Options are :

  • UDP port 161 and UDP 162
  • UDP port 513 and UDP 514
  • TCP port 513 and TCP 514
  • TCP port 161 and UDP 162
  • UDP port 161 and TCP 162
  • TCP port 161 and TCP 162

Answer :UDP port 161 and UDP 162

300-101 Implementing Cisco IP Routing (ROUTE) Practice Exam Set 2


Refer to the exhibit. From configuration displayed in the exhibit, which message does router R2 require to obtain IPV6 global address?


Options are :

  • Router solicitation
  • Neighbor solicitation
  • Neighbor solicitation
  • SLAAC DORA offer
  • Router advertisement

Answer :Router advertisement


Refer to the exhibit. A network engineer has observed that even when IP address 192.168.4.1 is unreachable, primary route remains installed on routing table. Given configuration displayed in exhibit, why is primary default static route not replaced by backup default static route?


Options are :

  • Primary default static route is not removed because only 6 SLAs are allowed in Cisco devices
  • Primary default static route is not removed because delay has been configured
  • Primary default static route is not removed because track feature is tracking wrong CISCO IP SLA
  • Primary default static route is not removed because it has better Administrative distance of 10

Answer :Primary default static route is not removed because track feature is tracking wrong CISCO IP SLA


Refer to the exhibit. From configuration displayed in the exhibit, which two statement are true? (choose two.)


Options are :

  • No routes from EIGRP will be redistributed to OSPF domain because there is no seed metric set
  • All routes learned from OSPF domain will be redistributed to EIGRP domain
  • All routes learned from EIGRP domain will be redistributed to OSPF domain
  • All routes learned from EIGRP domain will be redistributed to OSPF domain except the route denied by route-map EIGRP>to>OSPF
  • No routes from OSPF will be redistributed to EIGRP domain
  • Only network 10.3.8.0 learned from EIGRP domain will be redistributed on OSPF domain

Answer :All routes learned from OSPF domain will be redistributed to EIGRP domain All routes learned from EIGRP domain will be redistributed to OSPF domain

Cisco Data Center Architecture Set 4

Router CE-1 is located in Autonomous System 64511 and would like to advertise network 172.16.10.0/24 into BGP process. Which command will advertise the route?


Options are :

  • CE-1(config)#router bgp 64511 CE-1(config-router)#network 172.16.10.0 mask 255.255.255.0
  • CE-1(config)#router bgp 65411 CE-1(config-router)#network 172.16.10.0 mask 255.255.255.0
  • CE-1(config)#router bgp 64511 CE-1(config-router)#network 172.16.10.0 netmask 255.255.255.0
  • CE-1(config)#router bgp 64511 CE-1(config-router)#network 172.16.10.0 prefix 255.255.255.0

Answer :CE-1(config)#router bgp 64511 CE-1(config-router)#network 172.16.10.0 mask 255.255.255.0

Which packet switching method examines first packet in control plane, determines egress interface, builds forwarding  decision cache in data plane and all subsequent packets in the same flow will be forwarded based on flow cache information?


Options are :

  • Process switching
  • Modular Switching
  • Fragment Free Switching
  • Cisco Express Forwarding (CEF)
  • Cut-Through Switching
  • Fast Switching
  • Store-and-Forward Switching
  • Stackable Switching

Answer :Fast Switching

Policy-Based Routing (PBR) has been applied on Router R1 Ethernet 0/0 interface. Which statement is true if PBR matches implicit deny clause at the end of route-map?


Options are :

  • Packets entering e0/0 interface will be compared to PBR route-map, if PBR matches deny route-map clause, packet will be process switched and send to control plane for CPU forwarding decision.
  • Packets entering e0/0 interface will be compared to PBR route-map, if PBR matches deny route-map clause, packet will be dropped.
  • Packets entering e0/0 interface will be compared to PBR route-map, if PBR matches deny route-map clause, packet will be routed through normal forwarding process
  • Packets entering e0/0 interface will be compared to PBR route-map, if PBR matches deny route-map clause, packet will be fast switched and send to control plane for CPU forwarding decision.

Answer :Packets entering e0/0 interface will be compared to PBR route-map, if PBR matches deny route-map clause, packet will be routed through normal forwarding process

Cisco 210-060 Implement Collaboration Device Practice Exam Set 4

What four message types are used in Border Gateway Protocol (BGP)? (Choose four.)


Options are :

  • Query
  • Advertisement
  • Notification
  • Reply
  • Open
  • Database Description
  • Keepalive
  • Update
  • Ack

Answer :Notification Open Keepalive Update

Which mode of uRPF checks the source IP address of incoming packet with Forwarding Information Base (FIB) that is routable and that the packet arrived on the interface that router will use to send traffic back?


Options are :

  • Exact mode
  • Loose mode
  • VRF mode
  • Strict mode

Answer :Strict mode

Which of the following OSI layers are not protected by IPsec Transport mode configuration? (Choose Three.)


Options are :

  • Layer 3 – Network
  • Layer 4 – Transport
  • Layer 2 – Data Link
  • Layer 1 – Physical
  • Layer 5 – Session
  • Layer 6 – Presentation
  • Layer 7 – Application

Answer :Layer 3 – Network Layer 2 – Data Link Layer 1 – Physical

400-101 CCIE Routing and Switching Written Practice Exam Set 1


Refer to the exhibit. The network engineer has issued OSPF routing protocol configuration command displayed in exhibit.

Which cost value will be calculated for gigabit ethernet interface?


Options are :

  • 10
  • 1000
  • 1
  • 100

Answer :10

Which two of the following are characteristics of Dual Multi-homed connectivity? (Choose two.)


Options are :

  • Dual connections to one ISP
  • One link per ISP multi ISPs connections
  • More than two links per ISP
  • More than one link per ISP
  • More than one ISP connection
  • More than two ISP connections

Answer :More than one link per ISP More than one ISP connection


Refer to the exhibit. Router R1 serial 1/0 interface is configured with the IPv6 address 2001:db8:cafe:2::1/64. Which of these options would enable EIGRP for IPv6, with an AS of 1, on this interface?


Options are :

  • R1(config)# interface s1/0 R1(config-if)# ipv6 router eigrp 1
  • R1(config)# ipv6 router eigrp 1 R1(config-rtr)# enable 2001:db8:cafe:2::/64
  • R1(config)# ipv6 router eigrp 1 R1(config-rtr)# network 2001:db8:cafe:2::/64
  • R1(config)# interface s1/0 R1(config-if)# ipv6 eigrp 1

Answer :R1(config)# interface s1/0 R1(config-if)# ipv6 eigrp 1

400-101 CCIE Routing and Switching Written Practice Exam Set 5

•Which two of the following are Public assignable AS numbers? (Choose two.)


Options are :

  • 64,495
  • 65535
  • 64,497
  • 1
  • 0
  • 64,496

Answer :64,495 1


Refer to the exhibit. Which two statements are true? (Choose two)


Options are :

  • Router CE-1 has synchronized its time with NTP server with IP address 127.127.7.1
  • Router CE-1 is in passive mode
  • Router CE-1 is running NTP version 3
  • Router CE-1 is synchronized its time with NTP server that is authoritative clock at stratum 4
  • Router CE-1 is not receiving time from external source

Answer :Router CE-1 is running NTP version 3 Router CE-1 is not receiving time from external source

What are two Cisco IOS IP Service Level Agreement’s (SLAs) phases when using IP SLA responder? (Choose two.)


Options are :

  • Established Phase
  • Control Phase
  • Probing Phase
  • Active Phase
  • Idle Phase
  • Passive Phase

Answer :Control Phase Probing Phase

210-260 Implementing Cisco Network Security Practice Exam Set 1


Refer to the exhibit. Router R2 has been configured with IPv6 address EUI-64.

From configuration displayed in the exhibit, which IPv6 address router R1 should ping to test communication between router R1 and router R2?


Options are :

  • R1#ping 2001:DB8:CAFE:12::/64 eui-64
  • R1#ping 2001:DB8:CAFE:12:0053:A3FF:FE1A:4601
  • R1#ping 2001:DB8:CAFE:12:53:A31A:4601
  • R1#ping 2001:DB8:CAFE:12:253:A3FF:FE1A:4601

Answer :R1#ping 2001:DB8:CAFE:12:253:A3FF:FE1A:4601

Which command displays EIGRP adjacency information including neighbors address and incoming interface address?


Options are :

  • show ip eigrp neighbor
  • show ip route
  • show ip eigrp config
  • show ip eigrp topology

Answer :show ip eigrp neighbor

Which OSPF router type will generate Link State Advertisement (LSA) Type 7 – OSPF ASBR External LSA?


Options are :

  • Backbone Router
  • Backup Designated Router (BDR)
  • Area Border Router (ABR)
  • Designated Router (DR)
  • Internal Router
  • All OSPF routers
  • None, LSA Type 7 are legacy LSA and are not used anymore in OSPF
  • Autonomous System Boundary Router (ASBR)

Answer :Autonomous System Boundary Router (ASBR)

300-101 Implementing Cisco IP Routing (ROUTE) Practice Exam Set 2

Which tunneling protocol can encapsulate a Layer 3 protocol including multicast traffic and non-IP protocols but has no security?


Options are :

  • Generic Routing Encapsulation (GRE)
  • Next-Hop Resolution Protocol (NHRP)
  • Dynamic Multipoint Virtual Private Network (DMVPN)
  • IPsec (IP Security)

Answer :Generic Routing Encapsulation (GRE)

Company-A has single-homed connection to ISP-A. What command will enable Company-A’s edge router internet facing interface GigabitEthernet 0/1 to receive an IP address form ISP-A?


Options are :

  • Company-A(config)# interface GigabitEthernet 0/1 Company-A(config-if)# ip dhcp client Company-A(config-if)# no shutdown
  • Company-A(config)# interface GigabitEthernet 0/1 Company-A(config-if)# ip address default Company-A(config-if)# no shutdown
  • Company-A(config)# interface GigabitEthernet 0/1 Company-A(config-if)# ip address dhcp Company-A(config-if)# no shutdown
  • Company-A(config)# interface GigabitEthernet 0/1 Company-A(config-if)# ip address negotiated Company-A(config-if)# no shutdown

Answer :Company-A(config)# interface GigabitEthernet 0/1 Company-A(config-if)# ip address dhcp Company-A(config-if)# no shutdown

Which three routing protocol redistribution statements are true? (Choose three.)


Options are :

  • If metric parameter is not configured with redistribute command then the default-metric will be applied
  • Default seed metric for RIP is IGP metric value
  • Routing table of Boundary router doing redistributing routes will change
  • Metric parameter configured with redistribute command takes precedence over the default-metric and seed metric
  • If no metric parameter is configured with redistribute command and there is no default-metric configured then the seed metric will be applied
  • Redistribution is always performed inbound
  • Default Seed metric for OSPF protocol is Infinity, except BGP redistributed router where metric is 20

Answer :If metric parameter is not configured with redistribute command then the default-metric will be applied Metric parameter configured with redistribute command takes precedence over the default-metric and seed metric If no metric parameter is configured with redistribute command and there is no default-metric configured then the seed metric will be applied

200-125 Cisco Certified Network Associate (CCNA) Exam Set 4

Time-Based Access Control List (ACL) allows for ACL to be activated or deactivated at a specific time. Which two time ranges are available when configuring time-based ACL? (Choose two.)


Options are :

  • Periodic
  • Absolute
  • Active
  • Infinite
  • Forever
  • Repeated
  • Regular
  • Recurrent

Answer :Periodic Absolute

Authenticating route advertisement is important step to mitigate routing protocol update attack, where a rogue router can form neighbour adjacency  with legitimate routers and inject false route update information.

Route advertisement authentication can be achieved using plain text authentication or hashing authentication using Message Digest 5 (MD5) hash or Secure Hash Algorithm (SHA) hash.

Which of the following protocols support Secure Hash Algorithm authentication? (Select all that apply.)


Options are :

  • Open Shortest Path First version 2 (OSPFv2)
  • Enhanced Interior Gateway Protocol (EIGRP)
  • Open Shortest Path First version 2 (OSPFv3)
  • Routing Information Protocol version 2 (RIPv2)
  • Routing Information Protocol next generation (RIPng)
  • Border Gateway Protocol (BGP)

Answer :Open Shortest Path First version 2 (OSPFv2) Open Shortest Path First version 2 (OSPFv3) Routing Information Protocol next generation (RIPng)


Refer to the exhibit. R2 has connection to Internet and is connected to the Stub router R1. R2 is Propagating a Default Route to R1. R1 has connection to three LANs (LAN1, LAN2 and LAN3) and direct connection to R2. R1 is summarizing LAN networks to R2.

If a packet arrives at R1 from R2 with destination 10.1.0.1, what will be R1s next step?


Options are :

  • Flood the packet to all interfaces.
  • The destination does match summarized network so forward it to LAN interfaces in round robin
  • Since it will not match with any directly connected networks send it to default network towards R2
  • Match null0 summary route and discard the packet

Answer :Match null0 summary route and discard the packet

400-101 CCIE Routing and Switching Written Practice Exam Set 10


Refer to the exhibit. System administrator has issued command show ip cef switching statistics to see how many Drop and Punt packets there are. Some packets cannot be switched in data plane according to Forwarding Information Base (FIB) table and they are marked as “CEF punt”.

From output displayed in the exhibit, the system administrator can verify that there are some packets destined for router itself and some TTL expired Punt packets. Which other conditions can cause CEF punt? (Choose two.)


Options are :

  • Process switching enabled
  • Registry number mismatch
  • Mismatched authentication
  • Fast switching enabled
  • Packet must be fragmented
  • Encapsulation type not supported
  • Access list deny statement

Answer :Packet must be fragmented Encapsulation type not supported

In which OSPF network type there is no election of a Designated Router (DR) and Backup Designated Router (BDR)? (Choose four)


Options are :

  • Point-to-multipoint
  • Point-to-multipoint non-broadcast
  • Broadcast
  • Loopback
  • Non-broadcast
  • Point-to-point

Answer :Point-to-multipoint Point-to-multipoint non-broadcast Loopback Point-to-point

Network technician has started the following BGP configuration on CE-1 to set neighbour relationship with another router located in different AS:

CE-1(config)#router bgp 64495

Which statement is true regarding configuration of CE-1 AS number?


Options are :

  • Autonomous System Number (ASN) given is public and neighbour relationship will be eBGP
  • Autonomous System Number (ASN) given is 32bit AS, it will not work as only 16bit AS are used
  • Autonomous System Number (ASN) given is reserved and no neighbour relationship will be formed
  • Autonomous System Number (ASN) given is private and neighbour relationship will be iBGP

Answer :Autonomous System Number (ASN) given is public and neighbour relationship will be eBGP

210-260 Implementing Cisco Network Security Practice Exam Set 2

Which OSPF router type will generate Link State Advertisement (LSA) Type 3 – OSPF summary LSA?


Options are :

  • Area Border Router (ABR)
  • Internal Router
  • Designated Router (DR)
  • None, LSA Type 3 are legacy LSA and are not used anymore in OSPF
  • Backbone Router
  • Backup Designated Router (BDR)
  • All OSPF routers
  • Autonomous System Boundary Router (ASBR)

Answer :Area Border Router (ABR)

OSPF Hello and Dead timer interval must match between two routers to form a OSPF neighbor adjacency. What is default Hello/Dead interval in OSPF non-broadcast network type?


Options are :

  • Hello 10 seconds, Dead 30 seconds
  • Hello 30 seconds, Dead 120 seconds
  • Hello 30 seconds, Dead 90 seconds
  • Hello 10 seconds, Dead 40 seconds

Answer :Hello 30 seconds, Dead 120 seconds

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions