Cisco CCNP Route 300-101 Practice Tests Set 2

Company-A has single-homed connection to ISP-A, a system administrator is implementing routing from customer-A network towards ISP-A. What type of routing is recommended to be enabled on router R1 at customer site?


Options are :

  • Configure router R1 with static default route to any network via next-hop router R2
  • Configure router R1 to receive default OSPF route from ISP
  • Configure router R1 to receive default EIGRP route from ISP
  • Configure router R1 to receive default BGP route from ISP

Answer :Configure router R1 with static default route to any network via next-hop router R2

200-125 Cisco Certified Network Associate Practice Exam Set 11

What is the IPv6 multicast address used by OSPFv3 on all Designated Routers


Options are :

  • FF02::A
  • FF02::0
  • FF02::9
  • FF02::6
  • FF02::B
  • FF02::5

Answer :FF02::6

Controlling routing updates or route filtering is critical to ensure network operates efficiently. Which two methods can you use for controlling routing updates? (choose two)


Options are :

  • Distribute List
  • Route-maps
  • Variance
  • Administrative distance
  • Port Security
  • Metric

Answer :Distribute List Route-maps

Which path control features allow network performance and connectivity monitoring between two Cisco routers?


Options are :

  • Access control list
  • IP Service Level Agreements (SLAs)
  • Policy-Based Routing (PBR)
  • Distributed list
  • Route maps

Answer :IP Service Level Agreements (SLAs)

200-125 Cisco Certified Network Associate Practice Exam Set 10

Network Prefix Translation (NPTv6) is prefix translation for IPv6 similar to Network Address Translation for IPv4. What type of translation is NPTv6?


Options are :

  • One to Many
  • One to One
  • All to One
  • One to All
  • Many to One

Answer :One to One

Which mode of uRPF checks the source IP address of incoming packet with Forwarding Information Base (FIB) only if its routable?


Options are :

  • VRF mode
  • Exact mode
  • Strict mode
  • Loose mode

Answer :Loose mode

Which OSPF router type will generate Link State Advertisement (LSA) Type 1: OSPF Router LSA?


Options are :

  • Designated Router (DR)
  • Area Border Router (ABR)
  • None, LSA Type 1 are legacy LSA and are not used anymore in OSPF
  • Backbone Router
  • Autonomous System Boundary Router (ASBR)
  • Internal Router
  • All OSPF routers
  • Backup Designated Router (BDR)

Answer :All OSPF routers

100-105 Net Cert Interconnecting Cisco Networking Exam Set 8

BGP update messages are sent to BGP peers and update information on only one path. Which three following fields are seen in update message?


Options are :

  • BGP route identifier (routerID)
  • Version
  • Open send messages
  • Network layer reachability information (NLRI)
  • Withdrawn routes
  • Hold time
  • Path attributes

Answer :Network layer reachability information (NLRI) Withdrawn routes Path attributes

Router CE-1 and CE-2 from autonomous system 64511 are multihomed and would like to choose preferred exit path for entire autonomous system. Which BGP attribute can be configured on iBGP peers?


Options are :

  • MULTI_EXIT_DISC
  • ORIGIN
  • LOCAL_PREF
  • COMMUNITY
  • AS-PATH

Answer :LOCAL_PREF

What type of LSA is LSA Type 8?


Options are :

  • Link State Advertisement (LSA)
  • Intra-Area-router State Advertisement (LSA)
  • Inter-Area-prefix State Advertisement (LSA)
  • Intra-Area State Advertisement (LSA)

Answer :Link State Advertisement (LSA)

200-125 Cisco Certified Network Associate (CCNA) Exam Set 5


Refer to the exhibit. Based on configuration on the exhibit which two statements are true? (Choose two.)


Options are :

  • Packets sourced from PC-B will be policy routed
  • Packets sourced from PC-A will be policy routed
  • Packets sourced from PC-A will be sent through normal routing process
  • Packets sourced from PC-B will be dropped
  • Packets sourced from PC-B will be sent through normal routing process
  • Packets sourced from PC-A will be dropped

Answer :Packets sourced from PC-A will be policy routed Packets sourced from PC-B will be sent through normal routing process

In a network design that is based on the Cisco Enterprise Architecture, which three are primary modules when discussing the high-level overview? (Choose three.)


Options are :

  • Enterprise Branch
  • E-commerce
  • Enterprise Edge
  • Remote
  • Enterprise Campus

Answer :Enterprise Edge Remote Enterprise Campus

In Two-Tier Collapsed Core Hierarchical Network Design which three features are commonly supported at the access layer? (Choose three.)


Options are :

  • Power over Ethernet (PoE)
  • Policy-based security
  • Load balancing
  • Port security
  • QoS classification and marking
  • Redundancy

Answer :Power over Ethernet (PoE) Port security QoS classification and marking

300-320 Designing Cisco Network Service Architectures Exam Set 7

Some packets cannot be switched in data plane according to Forwarding Information Base (FIB) table and they are marked as “CEF punt”. CEF punts are forwarded to control plane for further processing. Which two conditions can cause CEF punt? (Choose two.)


Options are :

  • Process switching enabled
  • The IP Time-To-Live (TTL) has expired
  • Registry number mismatch
  • Mismatched authentication
  • Fast switching enabled
  • Packet must be fragmented
  • Access list deny statement

Answer :The IP Time-To-Live (TTL) has expired Packet must be fragmented

BGP speakers use BGP keepalive messages to confirm that the connection is alive. What are the default BGP keepalive and holdtime timers?


Options are :

  • Keepalive 5 seconds, holdtime 15 seconds
  • Keepalive 30 seconds, holdtime 120 seconds
  • Keepalive 10 seconds, holdtime 40 seconds
  • Keepalive 60 seconds, holdtime 180 seconds

Answer :Keepalive 60 seconds, holdtime 180 seconds


Refer to the exhibit. Router R2 is the boundary router and the administrator wants to perform mutual redistribution between protocols.

After completing redistribution commands on both protocols, administrator notices that OSPF routes are not being redistributed to EIGRP process, but EIGRP routes are being redistributed to OSPF.

What is a possible reason that EIGRP routes are not being redistributed?


Options are :

  • Keyword subnets is missing on redistribute command in EIGRP AS 100
  • Network statement 172.16.23.2 0.0.0.0 on router R2 in EIGRP AS 100 is wrong, 0.0.0.0 is reserved for default route
  • Wrong OSPF process is being redistributed in EIGRP AS 100
  • The metric value is wrong for the ospf command

Answer :Wrong OSPF process is being redistributed in EIGRP AS 100

200-105 Inter connecting Cisco Networking Devices Exam Set 1

Refer to the exhibit. Router CE-1 is configured to perform stateless one-to-one translation.

From configuration displayed in the exhibit, what type of translation is router CE-1 performing?


Options are :

  • NAT46
  • NPTv6
  • NAT64
  • NATv6
  • PATv6

Answer :NPTv6

True or False, IPv6 Extension Header is optional?


Options are :

  • False
  • True

Answer :True


Refer to the exhibit. Which NTP access-group command will not allow CE-1 router to update or synchronize itself with remote server? (Select all that apply.)


Options are :

  • peer
  • serve
  • query-only
  • serve-only

Answer :serve query-only serve-only

200-125 Cisco Certified Network Associate Practice Exam Set 6


Refer to the exhibit. A network engineer has configured IOS IP Service Level Agreements (SLAs). Which statement is true about configuration displayed in exhibit?


Options are :

  • Default route administrative distance will be 11, if IP address 192.168.4.1 is unreachable
  • Default Static route always has administrative distance of 1
  • Load balancing will occur if IP address 192.168.4.1 is unreachable
  • Preferred default will be removed in 10 second if IP SLA return code is “OK”

Answer :Default route administrative distance will be 11, if IP address 192.168.4.1 is unreachable

Which two authentication methods are supported on PPPoE client device? (Choose two)


Options are :

  • Challenge Handshake Authentication Protocol (CHAP)
  • Message-Digest Algorithm (MD5)
  • Password Authentication Protocol (PAP)
  • Secure Hash Algorithm (SHA)
  • Advanced Encryption Standard (AES)

Answer :Challenge Handshake Authentication Protocol (CHAP) Password Authentication Protocol (PAP)

Active Process Enhancement feature enables an EIGRP router to monitor the progression of the search for a successor route and ensure that the neighbor is still reachable.

Which type of EIGRP packet is sent when the active time is only half way through to help solve any SIA issue?


Options are :

  • SIA-Ack
  • SIA-Update
  • SIA-Reply
  • SIA-Hello
  • SIA-Query

Answer :SIA-Query

300-115 Implementing Cisco IP Switched Network Practice Exam Set 4


True or False, Refer to the exhibit.

Layer 2 MPLS VPN provides a Layer 2 service across the backbone. Layer 3 MPLS VPN provides a Layer 3 service across the backbone.

EIGRP needs to be enabled with the same AS number on both sides, CE-1<>PE-1 have same AS numbers as CE-2<>PE-2?


Options are :

  • False
  • True

Answer :False


Refer to the exhibit. Router R2 is the boundary router and the administrator wants to perform redistribution from OSPF process 1 to EIGRP process 100.

Which is the default seed metric that will be given to all OSPF routes redistributed to EIGRP? 


Options are :

  • 1 for all BGP routes
  • IGP metric value
  • 20
  • Infinity (0)
  • 1
  • 20 for all except BGP

Answer :Infinity (0)

In IPv6 network which device will perform packet fragmentation?


Options are :

  • Layer 2 Switch
  • Only Routers
  • Sending host
  • Multilayer Switch
  • Receiving host

Answer :Sending host

200-125 Cisco Certified Network Associate (CCNA) Exam Set 1


Refer to the exhibit. How is S1/0 interface on R1 enabled for RIPng?


Options are :

  • Interfaces are automatically enabled for RIPng when the RIPng process is started with ipv6 router rip CCNP_RIP command
  • Using the network 2001:db8:cafe:2::/64 CCNP_RIP interface command
  • Using the ipv6 rip CCNP_RIP enable interface command
  • Using the ipv6 unicast-routing global configuration command

Answer :Using the ipv6 rip CCNP_RIP enable interface command


Refer to the exhibit. System administrator has run command show ip bgp, and found out that local router is learning the path to network 10.1.1.0/24 from five valid BGP  peers (best path is hidden with ?). Based on the output which path will be chosen as best path by router CE-1 and offered to routing table?


Options are :

  • CE-1 router will use next hop BGP peer 172.25.0.4 because it has longest AS_Path attribute
  • CE-1 router will use next hop BGP peer 192.168.10.5 because it has been redistribution
  • CE-1 router will use next hop BGP peer 172.20.0.2 because it has lowest MED attribute
  • CE-1 router will use next hop BGP peer 172.25.0.4 because it has highest Weight attribute
  • CE-1 router will use next hop BGP peer 192.168.0.2 because it has highest LocPref attribute
  • CE-1 router will use next hop BGP peer 172.16.0.2 because it has shortest AS_Path attribute

Answer :CE-1 router will use next hop BGP peer 172.16.0.2 because it has shortest AS_Path attribute


Refer to the exhibit. Router CE-1 and router PE-1 are not able to for OSPF neighbor adjacency, based on configuration displayed in output, what is the cause of the problem? 


Options are :

  • Checksum between router CE-1 and router PE-1 does not match
  • On router PE-1 area 145 has been configured as stub
  • SPF algorithm has executed different times, there is no synchronization
  • Misconfigured authentication

Answer :On router PE-1 area 145 has been configured as stub

ICND1 100-105 Certification Practice Tests Set 2

OSPF Area 2 is a totally stub area, which Link State Advertisement (LSA) types are not allowed in this area?


Options are :

  • LSA Type 2: Network LSA
  • LSA Type 5: Autonomous system external LSA
  • LSA Type 4: Summary ASBR LSA
  • LSA Type 1: Router LSA
  • LSA Type 3: Summary LSA

Answer :LSA Type 5: Autonomous system external LSA LSA Type 4: Summary ASBR LSA LSA Type 3: Summary LSA

In which OSPF neighbor state routers exchange LSRequest and LSUpdate during neighbor database synchronization?


Options are :

  • Attempt
  • Down
  • Full
  • Init
  • EX-change
  • Loading
  • Two-way
  • EX-start

Answer :Loading

Network engineer is configuring OSPF full mesh topology over a nonbroadcast multiaccess (NBMA) network, Frame Relay. Routers are not forming OSPF adjacencies, which OSPF command could solve the problem?


Options are :

  • frame-relay lmi-type command
  • no frame-relay inverse-arp command
  • network area command
  • neighbor command

Answer :neighbor command

Cisco CCNP Route 300-101 Practice Tests Set 5


Refer to the exhibit. System administrator has run command show ip bgp, and found out that local router is learning the path to network 10.1.1.0/24 from five valid BGP  peers  (best path is hidden with ?). Based on the output which path will be chosen as best path by router CE-1 and offered to routing table?


Options are :

  • CE-1 router will use next hop BGP peer 192.168.10.5 because it has been redistribution
  • CE-1 router will use next hop BGP peer 172.25.0.4 because it has highest Weight attribute
  • CE-1 router will use next hop BGP peer 192.168.0.2 because it has highest LocPref attribute
  • CE-1 router will use next hop BGP peer 172.25.0.4 because it has longest AS_Path attribute
  • CE-1 router will use next hop BGP peer 172.20.0.2 because it has lowest LocPref attribute
  • CE-1 router will use next hop BGP peer 172.16.0.2 because it has shortest AS_Path attribute

Answer :CE-1 router will use next hop BGP peer 192.168.0.2 because it has highest LocPref attribute


Refer to the exhibit. System administrator is receiving the following OSPF message on router CE-1. Based on “Mismatched Authentication" message received which two statements are true? (Choose two.)


Options are :

  • OSPF authentication mismatch because Router with IP address 172.16.12.1 is configured with OSPF authentication type 2 (hash authentication)
  • OSPF authentication mismatch because CE-1 router is configured with OSPF authentication type 2 (hash authentication)
  • OSPF authentication mismatch because OSPF authentication is not enabled on router with ip address 172.16.12.2
  • OSPF authentication mismatch because Router with IP address 172.16.12.1 is configured with OSPF authentication type 0 (plain text authentication)
  • OSPF authentication mismatch because CE-1 router is configured with OSPF authentication type 0 (plain text authentication)
  • OSPF authentication mismatch because OSPF authentication is not enabled on router CE-1
  • OSPF authentication mismatch because Router with IP address 172.16.12.1 is configured with OSPF authentication type 2 (plain text authentication)

Answer :OSPF authentication mismatch because Router with IP address 172.16.12.1 is configured with OSPF authentication type 2 (hash authentication) OSPF authentication mismatch because OSPF authentication is not enabled on router CE-1


Refer to the exhibit. Which Cisco IOS command will produce this output?


Options are :

  • show ppp authentication
  • debug ppp negotiation
  • debug ppp authentication
  • show ppp negotiation

Answer :debug ppp authentication

200-125 Cisco Certified Network Associate (CCNA) Exam Set 5


Refer to the exhibit. Network administrator has successfully configured EIGRP authentication between router CE-1 and router PE-1 with the following command displayed on the exhibit using two alternating keys.

Network administrator is noticing that everyday neighbour relationship between router CE-1 and PE1 is getting torn down and then rebuilt again. What is the reason for this?


Options are :

  • Because there are two keys configured a new relationship will always be built when next key is active
  • Key lifetime should overlap so there is no period of time with no active keys
  • One of the keys should be infinite
  • Network administrator should use Secure Hash Algorithm (SHA) to stop neighbor adjacency rebuild

Answer :Key lifetime should overlap so there is no period of time with no active keys

The network engineer has reconfigured router-id in OSPF process but OSPF router-id remains the same. 

Which two are possible solutions for new router-id to take effect? (Choose two)


Options are :

  • Delete flash:nvram
  • Manual restart OSPF process
  • Shutdown and no-shutdown OSPF process
  • Reload the router

Answer :Manual restart OSPF process Reload the router

True or False, Encryption is a requirement of IPsec (IP Security)?


Options are :

  • False
  • True

Answer :False

200-105 Inter connecting Cisco Networking Devices Exam Set 3


Refer to the exhibit. Router R2 is the boundary router and the administrator wants to perform redistribution from EIGRP process 100 to OSPF process 1.

Which configuration will accomplish this?


Options are :

  • R2(config)#router ospf 1 R2(config-router)#redistribute eigrp metric 40 subnets
  • R2(config)#router eigrp 100 R2(config-router)#redistribute eigrp 100 to ospf 1 all-subnets
  • R2(config)#router eigrp 100 R2(config-router)#redistribute eigrp 100 metric-type 1
  • R2(config)#router ospf 1 R2(config-router)#redistribute eigrp 100 subnets

Answer :R2(config)#router ospf 1 R2(config-router)#redistribute eigrp 100 subnets


Refer to the exhibit. Which statement is true given the output displayed in the exhibit? 


Options are :

  • Cisco IOS IP Service Level Agreements (SLAs) is down
  • There is no default route for router R1
  • Track feature is tracking CISCO IP SLA 6
  • New default route has administrative distance of 11

Answer :New default route has administrative distance of 11

There are four BGP attribute types

     Well-known mandatory,

     Well-known discretionary,

     Optional transitive and

     Optional non-transitive

Which BGP attribute is well known discretionary?


Options are :

  • LOCAL_PREF
  • NEXT_HOP
  • ORIGIN
  • MUTLI_EXIT_DISC
  • AS_PATH

Answer :LOCAL_PREF

210-065 Implementing Cisco Video Network Devices Exam Set 6


Refer to the exhibit. Which statement is true given the output displayed in the exhibit?


Options are :

  • Router R1 is configured with Multiprotocol Label Switching (MPLS) VPNs
  • Router R1 is configured with Virtual Route Forwarding (VRF)-lite
  • Router R1 is configured with Easy Virtual Network (EVN)
  • Router R1 is configured with Layer 2 Tunneling Protocol Version 3 (L2TPv3)
  • Router R1 is configured with multipoint generic routing encapsulation (mGRE)

Answer :Router R1 is configured with Easy Virtual Network (EVN)

Which authentication methods does EIGRP support? (Select all that apply.) 


Options are :

  • Message Digest 5 (MD5)
  • Periodic Authentication
  • Area authentication
  • Secure Hash Algorithm (SHA) hash
  • Absolute authentication
  • Plain text authentication

Answer :Message Digest 5 (MD5)

Authenticating route advertisement is important step to mitigate routing protocol update attack, where a rogue router can form neighbour adjacency  with legitimate routers and inject false route update information.

Route advertisement authentication can be achieved using plain text authentication or hashing authentication using Message Digest 5 (MD5) hash or Secure Hash Algorithm (SHA) hash.

Which of the following protocols support plain text authentication? (Select all that apply.)


Options are :

  • Routing Information Protocol next generation (RIPng)
  • Routing Information Protocol version 2 (RIPv2)
  • Open Shortest Path First version 2 (OSPFv2)
  • Open Shortest Path First version 2 (OSPFv3)
  • Enhanced Interior Gateway Protocol (EIGRP)
  • Border Gateway Protocol (BGP)

Answer :Routing Information Protocol version 2 (RIPv2) Open Shortest Path First version 2 (OSPFv2)

200-105 Inter connecting Cisco Networking Devices Exam Set 5

Which of these three statements about Network Prefix Translation (NPTv6)  are true? (Choose three.)


Options are :

  • Global IPv6 addresses are not supported
  • Multicast is not supported
  • Firewall is not supported
  • NPTv6 is stateful translation
  • Virtual Routing and Forwarding (VRF) is not supported
  • NTPv6 is successor of NAT64
  • Conserves IPv4 address
  • NPTv6 is one-to-many prefix translation

Answer :Multicast is not supported Firewall is not supported Virtual Routing and Forwarding (VRF) is not supported


Refer to the exhibit. The system administrator has issued command show ip interface ethernet 0/0. From output displayed in the exhibit, which packet switching method is being used on interface e0/0?


Options are :

  • Flow switching
  • Process switching
  • Fast switching
  • Cisco Express Forwarding (CEF)

Answer :Fast switching

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions