642-732 Conducting Cisco Unified Wireless Site Survey Exam Set 1

An engineer is configuring an AP for a site survey. How should the transmit power be configured?


Options are :

  • Set to maximum power
  • Set to one level below full power
  • Set to one level above the lowest power level.
  • Enable DTPC

Answer : Set to one level below full power

Cisco 300-209 Implementing Secure Mobility Solutions Exam Set 5

An engineer is conducting a site calibration using Cisco WCS. The current network has 802.11a, 802.11b, 802.11g, and 802.11n devices. How many times should the calibration be done?


Options are :

  • once for each band
  • once for each protocol
  • once using each data collection type
  • once per deployment

Answer : once for each band

The customer requires connectivity between two buildings that are 100 meters apart. Which type of antenna is suitable for this installation?


Options are :

  • dipole antenna
  • patch antenna
  • sector antenna
  • parabolic antenna

Answer : parabolic antenna

A network engineer is conducting a Layer 1 site survey using a spectrum analyzer. Which four RF sources can be detected? (Choose four.)


Options are :

  • A,B,C,D
  • Bluetooth
  • infrared
  • analog TV
  • microwave
  • jammers
  • 3G phone
  • GSM phone
  • cordless phones

Answer : A,B,C,D

Cisco 210-060 Implement Collaboration Device Practice Exam Set 3

An engineer is planning for a 24 Mbps data rate for a new installation. If the environment and other factors are not taken into consideration, what is the coverage area from the AP?


Options are :

  • 100 feet
  • 150 feet
  • 80 feet
  • 40 feet
  • 225 feet

Answer : 80 feet

After installation of a new data-only wireless network, an engineer found that RRM has set all of the APs to a power level of 1. Which option describes the reason for this?


Options are :

  • APs should be manually set initially.
  • APs are too far apart for the set data rates.
  • TPC needs to be enabled.
  • EDRRM is enabled.
  • High co-channel interference exists.
  • DTPC value is set too high.

Answer : APs are too far apart for the set data rates.

A customer is preparing for a site survey. The building is in the middle of construction and not all walls are constructed. What is the most practical way to do this site survey?


Options are :

  • Add 2.5 APs on every floor to compensate for future RF blocks
  • Conduct a passive survey of the facility using temporary APs.
  • Use Cisco WCS planning mode to conduct the site survey and file a proposal to the customer.
  • Obtain architect drawings of the facilities with dimensions and floor height.

Answer : Use Cisco WCS planning mode to conduct the site survey and file a proposal to the customer.

200-105 Interconnecting Cisco Networking Devices Part Exam Set 2

A customer has requested site surveys for data, voice, video, and location services for their location. The customer will be using RFID tags extensively. Which type of site survey should be conducted?


Options are :

  • voice
  • multi-survey
  • bridging
  • data
  • location-based services
  • video

Answer : location-based services

An engineer is adding APs to an existing VoWLAN to allow for location based services. Which option will the primary change be to the network?


Options are :

  • increased transmit power on all APs
  • cell overlap would decrease
  • AP footprint
  • triangulation of devices
  • moving to a bridging model

Answer : AP footprint

A network engineer is conducting an active wireless survey. Which four actions must be performed to ensure a successful survey? (Choose four.)


Options are :

  • Use the same AP model for the survey that is used in production.
  • A,E,F,G
  • Look for potential barriers of the propagation of RF signals.
  • Place the survey laptop antenna on a pole while surveying
  • Perform the survey when site is empty.
  • Identify areas that have high user density
  • Use the same wireless devices that the customer will use.
  • Point the antenna of the survey laptop towards the access point.

Answer : A,E,F,G

200-125 Cisco Certified Network Associate Practice Exam Set 5

A customer wants to trade in older 802.11a/b/g access points for new 802.11n access points. What must be considered before deploying new 802.11n access points?


Options are :

  • Fewer access points are needed because 802.11n has better coverage.
  • Fewer APs are needed because 802.11n runs on a different radio frequency.
  • 5-GHz coverage is needed when expecting 300-450 Mbps client link.
  • New APs should bundle channels 1, 6, and 11 to increase throughput to 150 Mbps.

Answer : 5-GHz coverage is needed when expecting 300-450 Mbps client link.

An engineer needs to perform a site calibration using Cisco WCS. Which two types of data collection can be used? (Choose two.)


Options are :

  • radius point
  • area point
  • A,D
  • location point
  • linear point
  • hybrid point
  • data point

Answer : A,D

A 802.11n implementation is being discussed. Users are satisfied with the potential 300-450 Mbps throughput of new 802.11n APs. Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)


Options are :

  • Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link
  • 450 Mbps throughput is the client max for 5-GHz radio.
  • 300 Mbps throughput is the client max for 2.4-GHz radio
  • CleanAir helps clear noise for 802.11n channel bonding to work.
  • The remaining bandwidth is divided per device when more clients are connected to one AP.
  • 100 Mbps AP Ethernet switch port is a potential bottleneck.
  • C,E.F

Answer : C,E.F

400-101 CCIE Routing and Switching Written Practice Exam Set 9

What document must be kept current when a customer is conducting network maintenance?


Options are :

  • installation report
  • survey report
  • technical repor
  • readiness report

Answer : installation report

What two tools can an engineer use to verify RF data rates and coverage after installation? (Choose two.)


Options are :

  • Cisco WCS Location Readiness Tool
  • Cisco WCS Planning Mode
  • AirMagnet Active Survey Mode
  • AirMagnet Planner Mode
  • Cisco WCS Voice Audit Report
  • D,E
  • AirMagnet Passive Survey Mode

Answer : D,E

The customer has 50 lightweight APs and a WLC license for 50 APs. The customer also has 50 autonomous APs that will be converted to lightweight. How can the autonomous APs be joined to the current WLC?


Options are :

  • Install an additional license for the 50 APs on the WLC.
  • Convert the 50 autonomous AP licenses on the WLC.
  • Convert the autonomous AP license to a CAPWAP license.
  • Deploy Cisco WCS to automatically license the converted autonomous APs

Answer : Install an additional license for the 50 APs on the WLC.

200-310 Designing for Cisco Inter network Solutions Exam Set 1

An engineer has WLC redundancy included in WLAN design documentation, where the WLCs are loaded to half the license capacity therefore allowing half the WLCs to fail without an AP going offline at a given time. What redundancy model does this describe?


Options are :

  • N+1
  • N+N
  • N+N+1
  • N+1+1

Answer : N+N

A company has requested an indoor wireless survey that supports 5GHz radio, 3x4 MIMO technology, and 3 spatial streams. Which AP is used to perform this survey?


Options are :

  • 600
  • 1242
  • 2600
  • 3600
  • 1600

Answer : 2600

An engineer notes that some areas of a floor fail when using the Location Readiness Tool in Cisco WCS. What criteria must be met for a point to be considered location ready?


Options are :

  • one AP in each quadrant, with two less than 70 feet away
  • one AP in three quadrants, with two less than 70 feet away
  • one AP in three quadrants, with one less than 70 feet away
  • one AP in each quadrant, with three less than 70 feet away

Answer : one AP in each quadrant, with three less than 70 feet away

400-101 CCIE Routing and Switching Written Practice Exam Set 5

An engineer is conducting a failover test with a Mesh deployment by disconnecting the network interface of a RAP. A MAP becomes stranded even though it has an acceptable RSSI value on the link to its neighbor. What are two reasons the MAP may become stranded? (Choose two.)


Options are :

  • the SNR on the neighbor link is 15dB
  • B,C
  • the MAP is 6 hops away
  • the SNR on the neighbor link is 5dB
  • the throughput on the neighbor link is 24Mbps
  • the throughput on the neighbor link is 18Mbps
  • the MAP is 9 hops away

Answer : B,C

Which CCX version is the minimum necessary on a client when adding data points during WCS Calibration?


Options are :

  • CCXv3
  • CCXv1
  • CCXv4
  • CCXv2
  • CCXv5

Answer : CCXv2

A site survey proposes placement of new APs to replace older APs. Which three options are three potential placements of the new APs? (Choose three.)


Options are :

  • Mount new APs on the exact location according to site survey report.
  • Use the old placements where they are near the proposed location.
  • Deploy APs every 3000 square feet
  • A,B,C
  • Use network cables and mounting brackets from the older installation.
  • Deploy APs every 4000 square feet
  • Add APs from the site survey that have no APs in older installation.

Answer : A,B,C

210-260 Implementing Cisco Network Security Practice Exam Set 1

An engineer is surveying a customer site for additional wireless coverage. What two menus will an engineer navigate to in order to determine the maximum number of supported APs? (Choose two.)


Options are :

  • Wireless - Access Points
  • Monitor - Summary
  • Controller - Inventory
  • A,B
  • Management - Summary
  • Monitor - Access Points

Answer : A,B

An engineer is conducting a site survey for use of Cisco 7925 wireless clients. Which two design criteria are necessary to ensure proper network design? (Choose two.)


Options are :

  • -72 dBm RSSI or better
  • -67 dBm RSSI or better
  • 15 percent overlap
  • 20 percent overlap
  • 25 percent overlap
  • -65 dBm RSSI or better
  • B,E

Answer : B,E

An engineer would like to calibrate the RF environment to improve accuracy. What wireless attribute is added to the floor-level calculation by calibrating the floor?


Options are :

  • SNR
  • multipath
  • attenuation
  • TX power

Answer : attenuation

400-101 CCIE Routing and Switching Written Practice Exam Set 7

On which two items will data be collected when an engineer is conducting a passive survey? (Choose two.)


Options are :

  • roaming
  • rouges
  • rate shifting data rates
  • encryption
  • A,D
  • RF interference

Answer : A,D

Which three post-installation checks should an engineer perform after a new wireless installation? (Choose three.)


Options are :

  • Verify that the minimum data rate is 24 Mbps.
  • Conduct a passive survey of 802.11a and 802.11b.
  • Check for adequate signal levels as surveyed.
  • Verify that the cell overlap is 20%.
  • Conduct a passive and active survey of each media type in use.
  • Check for co-channel interference.
  • A,B,D

Answer : A,B,D

Which three pieces of information should be included in an installation report? (Choose three.)


Options are :

  • software versions of each AP
  • radio status for each AP
  • configuration files for each WLC
  • A,B,E
  • switch connection for each MAP
  • license file for each RAP
  • mobility group name for each WLC

Answer : A,B,E

300-320 Designing Cisco Network Service Architectures Exam Set 4

An engineer is performing a data collection to validate wireless coverage. At what two locations should a linear point collection be performed? (Choose two.)


Options are :

  • office cubicles
  • conference rooms
  • C,D
  • auditorium
  • warehouse
  • private offices

Answer : C,D

A Cisco engineer is troubleshooting a Cisco 1250 series 802.11n access point with a maximum throughput on 2.4 GHz that is limited to 72 Mbps. Why might the AP be operating in a limited capacity?


Options are :

  • the 2.4 GHz is 40 MHz wide
  • the switch providing PoE supports 802.3af
  • the switch providing PoE supports 802.3at
  • the 2.4 GHz bandwidth is 20 MHz wide

Answer : the switch providing PoE supports 802.3af

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions