642-732 Conducting Cisco Unified Wireless Site Survey Exam Set 6

Which tool can best provide throughput verification?


Options are :

  • InSSIDer
  • Xirrus Wi-Fi Inspector
  • WLC > Monitor > Clients > LinkTest
  • WaveDeploy

Answer : WaveDeploy

642-732 Conducting Cisco Unified Wireless Site Survey Exam Set 2

When performing a post-installation audit using the Ekahau Survey tool, which four steps are associated with the passive portion of the audit? (Choose four.)


Options are :

  • Survey by SSID to ensure that smooth roaming is taking place.
  • Verify that the real-world network traffic (for example, physical data rate, packet loss, etc.) meets user requirements.
  • A,B,D,E
  • Check to see if the signal levels on other access points that are heard on the same channel are at least 19 dBm weaker than the access point that you are next to.
  • Check that all channels are supported by the APs regardless of client capabilities.
  • When you have completed the post-installation surveys, compare them to the surveys that were performed before the installation. They should look nearly identical.
  • Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel.

Answer : A,B,D,E

What is a typical attenuation value for a cinder block wall?


Options are :

  • 6dB
  • 12dB
  • 3dB
  • 4dB

Answer : 4dB

Before installing new wireless hardware, an engineer collects information from the facility using Cisco Spectrum Expert. What three devices would be detected during this survey? (Choose three.)


Options are :

  • DECT phone
  • wireless printer
  • weather radio
  • fire alarm
  • Magnavox TV
  • A,C,F
  • Linksys router

Answer : A,C,F

200-125 Cisco Certified Network Associate Practice Exam Set 3

An engineer is conducting a VoWLAN survey for voice clients with a max power of 40 mW. What power level should the engineer set the AP to during the survey?


Options are :

  • 10 mW
  • 40 mW
  • 30 mW
  • 5 mW
  • 20 mW

Answer : 20 mW

An engineer is conducting a passive survey. On what two items will data be collected? (Choose two.)


Options are :

  • RF interference
  • roaming
  • A,D
  • rate shifting data rates
  • encryption
  • rouges

Answer : A,D

Which two details are specified in the Executive Summary section of the Site Survey Report? (Choose two.)


Options are :

  • C,D
  • proposed location for each AP
  • expressed requirements set by customer
  • total number of APs
  • customer and site surveyor contact details
  • coverage map

Answer : C,D

Cisco 300-209 Implementing Secure Mobility Solutions Exam Set 3

What RF phenomenon results from a presence of metallic I-beams, conveyor belts, chain-link fences, and metallic shelves found in a warehousing environment?


Options are :

  • scattering
  • absorption
  • free path loss
  • multipath

Answer : multipath

Which two types of information should be included in the installation inventory portion of the post-installation report? (Choose two.)


Options are :

  • Results of the coverage audit performed with the site survey mapping tool
  • All AP, controller, and MSE administrator credentials
  • The number and type of all WLAN clients and tags
  • A,C
  • The names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the WLAN

Answer : A,C

When performing a site survey, what is a typical usable range for client signal strength?


Options are :

  • -45 to -65 dBm
  • -30 to -50 dBm
  • -70 to -90 dBm
  • -60 to -80 dBm

Answer : -60 to -80 dBm

300-320 Designing Cisco Network Service Architectures Exam Set 1

A company has requested an indoor wireless survey in a multi-tenant building for 2.4GHz data and 5GHz voice services. Data clients will require three spatial streams and 4x4 MIMO technology. What is the Cisco recommended Access Point for performing this survey?


Options are :

  • 600
  • 3600
  • 1600
  • 2600

Answer : 3600

When designing a WLAN, AP placement is important. How would you rank the density of APs needed to support location services versus data and voice services?


Options are :

  • Voice and data services both require a higher density of APs than location services.
  • Data services have a lower density of APs compared to location services, but more than voice.
  • Data services have the lowest density of APs compared to location services, which has the highest density.
  • Voice services have the highest density of APs over location and data services.

Answer : Data services have the lowest density of APs compared to location services, which has the highest density.

Which three types of WLAN data, location, and voice testing should be included in the installation customer report? (Choose three.)


Options are :

  • Results from Cisco Unified Communications Manager cluster failover tests
  • A,D,F
  • Results of the WCS planning tool
  • Results of the coverage audit performed with the site survey mapping tool per media installed on 802.11a/b/g/n networks
  • Results from a WCS WLAN client audit
  • Results from an ISP throughput test
  • Results of a location readiness test

Answer : A,D,F

300-320 Designing Cisco Network Service Architectures Exam Set 5

A wireless engineer is gathering equipment to perform a point-to-point bridge survey. What three pieces of equipment should be used? (Choose three.)


Options are :

  • 3502i with dual band directional antennas
  • 1142 Series with internal antennas
  • B,E,F
  • 1310 with internal antenna
  • 1552e with three AIR-ANT2547-N=
  • 1552e with AIR-ANT2588P3M-N=
  • 1132 with a 10dBi Yagi
  • 3502e with AIR-ANT2460NP-R

Answer : B,E,F

Which three types of information should be included in the post-installation customer report? (Choose three.)


Options are :

  • Naming convention for APs and controllers
  • The number of licenses consumed by clients and tags at installation
  • A,C,E
  • VLAN structure and naming convention
  • Throughput and dB loss for all fiber-optic backbone connections
  • Any locations in the WLAN coverage that are secure and require special access
  • Reachability status for all WLAN clients and tags

Answer : A,C,E

When planning a site survey, what Cisco tool can an engineer use to estimate the number of required APs?


Options are :

  • WLC NetFlow Exporter
  • WCS Planning Mode
  • MSE Location Tracking
  • WCS Map Editor
  • LWAP Monitor Mode

Answer : WCS Planning Mode

100-105 Net Cert Interconnecting Cisco Networking Exam Set 5

An engineer is performing a site survey for a 5 GHz mesh wireless network. The customer requires 300 Mbps data rates per radio, 2x3 MIMO technology, and legacy beamforming. What Cisco access point should be recommended?


Options are :

  • 1524
  • 1522
  • 1510
  • 1552

Answer : 1552

What three best practices should be performed for a Data-Only Survey? (Choose three.)


Options are :

  • 5 - 10 percent overlap
  • reduce the power to 75% of the client max power
  • reduce the power to 50% of the client max power
  • enable DTPC
  • disable DTPC
  • 10 - 15 percent overlap
  • A,C,F

Answer : A,C,F

The customer site requires Cisco 1400 bridges with 28dBi external antennas in a PTP design. What is the maximum power setting allowed by Cisco?


Options are :

  • 155 mW
  • 150 mW
  • 160 mW
  • 145 mW

Answer : 155 mW

Cisco 300-209 Implementing Secure Mobility Solutions Exam Set 5

What type of survey is used to assess and analyze existing wireless infrastructure?


Options are :

  • predictive survey
  • passive survey
  • application survey
  • active survey

Answer : passive survey

An engineer is deploying an outdoor Mesh network. What are the four major factors that should be considered? (Choose four.)


Options are :

  • mounting
  • A,B,D,G
  • power
  • network connectivity
  • satellite dishes
  • traffic lights
  • line of sight
  • buildings
  • power lines

Answer : A,B,D,G

A company needs to link two buildings, separated by 100 feet of parking lot, with Cisco 1300 bridges. Which three Cisco recommended antennas should be used? (Choose three.)


Options are :

  • AIR-ANT2410Y-R
  • AIR-ANT1728
  • AIR-ANT24120
  • AIR-ANT2506
  • AIR-ANT1949
  • AIR-ANT5959
  • B,E,F

Answer : B,E,F

200-105 Inter connecting Cisco Networking Devices Exam Set 2

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions