300-115 Implementing Cisco IP Switched Network Practice Exam Set 4

A new switch that contains a configuration consisting of only VLAN 5 was just added to the network. Now users assigned to VLANs 9 and 10 are complaining of communication problems.Using the show vlan command, you discover that only VLAN 5 and the default VLANs exist on all your switches. What could have caused this problem?


Options are :

  • The new switch was configured in server mode and the revision number was higher than the current number in the network.
  • The domain name on the new switch did not match the rest of the network.
  • The new switch was configured in server mode and the revision number was lower than the current number in the network.
  • The new switch had the default password set.

Answer : The new switch was configured in server mode and the revision number was higher than the current number in the network.

What are the three RSTP port states? (Choose three.)


Options are :

  • Learning
  • Listening
  • Initializing
  • .Forwarding
  • .Discarding
  • .Blocking

Answer : Learning .Forwarding .Discarding

200-125 Cisco Certified Network Associate Practice Exam Set 10

Which IOS commands are entered in interface configuration mode to configure a switch port to actively negotiate to be an 802.1Q trunk port? (Choose two.)


Options are :

  • switchport trunk dot1q
  • .switchport trunk allowed vlan
  • .switchport mode dynamic auto
  • switchport mode trunk
  • switchport trunk encapsulation dot1q

Answer : switchport mode trunk switchport trunk encapsulation dot1q

How long does it take for a port to transition from the STP blocking state to the forwarding state by default?


Options are :

  • 25 seconds
  • 10 seconds
  • 50 seconds
  • .2 seconds

Answer : 50 seconds

Which devices are required to provide connectivity between VLANs? (Choose two.)


Options are :

  • .router
  • multilayer switch
  • bridge
  • hub

Answer : .router multilayer switch

210-260 Implementing Cisco Network Security Practice Exam Set 3

What Cisco switch feature allows IP phones to be automatically placed into a separate VLAN from data traffic?


Options are :

  • marking
  • private VLANs
  • auxiliary VLANs
  • AutoQoS

Answer : auxiliary VLANs

Which statement best describes the interaction between a workstation and an HSRP virtual router?


Options are :

  • The active HSRP router replies to the workstation's ARP request with the virtual router's MAC address.
  • The workstation must support IRDP in order to switch to the alternate router in an HSRP group.
  • The workstation must have the real IP address of one of the HSRP routers defined as its default gateway.
  • The workstation sends packets to the active router's real MAC address.

Answer : The active HSRP router replies to the workstation's ARP request with the virtual router's MAC address.

200-125 Cisco Certified Network Associate Practice Exam Set 12

In which HSRP state is the router a candidate to become the next active router for the group


Options are :

  • Learn
  • Standby
  • .Listen
  • Initial
  • Backup

Answer : Standby

Which of the following statements are TRUE about the selection of the active router in an HSRP group? (Choose two.)


Options are :

  • The router with the highest priority becomes the active router.
  • The router with the lowest priority becomes the active router.
  • The router with the lowest IP address becomes the active router if the priorities of all routers are the same.
  • The router with the highest IP address becomes the active router if the priorities of all routers are the same.

Answer : The router with the highest priority becomes the active router. The router with the highest IP address becomes the active router if the priorities of all routers are the same.

Which of the following sets of commands CANNOT be included in the plan to implement HSRP on a Layer 3 switch port?


Options are :

  • .interface port-channelno switchport
  • interface vlanip address
  • interface fastethernetswitchport mode access
  • interface fastethernetno switchportip address

Answer : interface vlanip address

200-125 Cisco Certified Network Associate Practice Exam Set 10

Which two of the following procedures can be performed on a VTP server to reset the VTP configuration revision number to 0? (Choose two. Each correct answer is a complete solution.)


Options are :

  • Disable VTP pruning, then enable VTP pruning.
  • .Change the VTP mode to transparent, then back to server mode.
  • Change the VTP domain name to a non-existent domain name, and then back to the correct domain name.
  • Change the VTP mode to client, and then back to server mode.

Answer : .Change the VTP mode to transparent, then back to server mode. Change the VTP domain name to a non-existent domain name, and then back to the correct domain name.

What is the first step STP performs to establish a loop-free spanning tree in a switched network?


Options are :

  • Elects a root switch
  • Selects a designated switch for each switched segment
  • Sets a priority for each redundant link
  • Disables redundant loops in the tree

Answer : Elects a root switch

Which virtual router states are defined in the GLBP protocol? (Choose two.)


Options are :

  • Primary gateway
  • Active secondary gateway
  • Active virtual gateway
  • Active virtual forwarder
  • Backup gateway

Answer : Active virtual gateway Active virtual forwarder

200-105 Inter connecting Cisco Networking Devices Exam Set 1

Which three methods can be used to manage Cisco APs that are running autonomously? (Choose three.)


Options are :

  • WLSE
  • WCS
  • Web interface
  • WLC
  • .CLI

Answer : WLSE Web interface .CLI

How is load balancing achieved when implementing HSRP?


Options are :

  • .By using multiple HSRP groups
  • By configuring multiple virtual router addresses
  • By configuring the same priority on all HSRP group members
  • By configuring multiple gateways on the routers

Answer : .By using multiple HSRP groups

Which two tables are used by Cisco Express Forwarding? (Choose two.)


Options are :

  • FIB
  • Adjacency table
  • Routing table
  • MAC address table
  • ACL table

Answer : FIB Adjacency table

200-105 Inter connecting Cisco Networking Devices Exam Set 5

Which routers comprise a VRRP group?


Options are :

  • Primary and secondary
  • Master and backup
  • Active and standby
  • Host and client

Answer : Master and backup

Which IOS command configures the switch for the VTP mode that will propagate its VLAN database changes to others in the domain?


Options are :

  • vtp v1-mode
  • vtp mode server
  • vtp mode client
  • vtp transparent mode

Answer : vtp mode server

When executed on a HSRP group member named Router 10, what effect does the following command have? Router10(config-if)# standby 1 track serial0 25


Options are :

  • .It will cause the router to increase its HSRP priority by 25 if the Serial0 interface on the standby router goes down
  • .It will cause the router to decrement its HSRP priority by 25 if Serial 0 goes down
  • .It will cause the router to notify Router 25 is serial 0 goes down
  • It will cause the router to shut down the Serial0 interface if 25 packets have been dropped

Answer : .It will cause the router to decrement its HSRP priority by 25 if Serial 0 goes down

400-101 CCIE Routing and Switching Written Practice Exam Set 1

You need to create an implementation plan for providing Layer 3 redundancy in your switched network. You included Hot Standby Routing Protocol (HSRP) as the protocol to avoid first-hop router failure. However, your supervisor suggests including Virtual Router Redundancy Protocol (VRRP) instead of HSRP in the implementation plan. Which of the following statements is TRUE about the reasons for the suggested change in the implementation plan? (Choose two.)


Options are :

  • HSRP works only on Cisco routers and VRRP works on both Cisco and non- Cisco routers.
  • HSRP-enabled routers automatically preempt the active router and VRRP-enabled routers need to be configured manually to preempt the active router.
  • HSRP-enabled routers need to be configured manually to preempt the active router and VRRP-enabled routers preempt it automatically.
  • HSRP works on both Cisco and non-Cisco routers and VRRP works only Cisco routers.

Answer : HSRP works only on Cisco routers and VRRP works on both Cisco and non- Cisco routers. HSRP-enabled routers need to be configured manually to preempt the active router and VRRP-enabled routers preempt it automatically.

Which Cisco component can be enabled on a switch port connected to a workstation to dramatically decrease the time a workstation must wait for spanning tree to converge?


Options are :

  • .PortFast
  • .EtherChannel
  • FastEthernet
  • UplinkFast

Answer : .PortFast

What command should you use to quickly view the HSRP state of the switch for all HSRP groups of which the switch is a member?


Options are :

  • switch# show standby
  • switch# show hsrp
  • switch# show ip interface brief
  • switch# show standby brief

Answer : switch# show standby brief

200-125 Cisco Certified Network Associate Practice Exam Set 9

When using auxiliary VLANs, how is a phone configured with the appropriate VLAN to join?


Options are :

  • the switch connected to the phone provides the VLAN
  • a VMPS server provides the VLAN for the switch and phone
  • the PC attached to the phone provides the VLAN information
  • the administrator configures the phone with CLI

Answer : the switch connected to the phone provides the VLAN

Which of the following is required to allow load balancing between three HSRP routers connected to the same LAN?


Options are :

  • .Two HSRP groups, each with an active router
  • A single HSRP group with all three routers as active routers for the group
  • Two HSRP groups with one active router for both the groups
  • Three HSRP groups, each with an active router
  • A single HSRP group with one active router for the group

Answer : Three HSRP groups, each with an active router

Which VLAN trunking protocol adds four bytes to the Ethernet frames?


Options are :

  • 802.1
  • 802.1Q
  • LANE
  • .ISL

Answer : 802.1Q

Cisco 100-101 Interconnecting Cisco Networking Devices Exam Set 1

You are troubleshooting a problem with two routers configured in a HSRP group. You intended to configure the routers so that Router A and Router B would each track their respective Fa0/1 interfaces and decrement their priorities for several VLAN groups if the tracked interface went down. However, you find that Router A is not taking over as the active device for the HSRP group on VLAN 101 when the Fa0/1 interface on Router B fails. Which command would NOT be useful for discovering the problem?


Options are :

  • show standby
  • show vlans
  • show standby brief
  • .show running-configuration

Answer : show vlans

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions