300-115 Implementing Cisco IP Switched Network Practice Exam Set 3

Which of the following capabilities does a multilayer switch possess that an Access layer switch does not? (Choose all that apply.)


Options are :

  • the ability to make forwarding decisions based on host names
  • the ability to make forwarding decisions based on IP addresses
  • the ability to make forwarding decisions based on MAC addresses
  • .the ability to make forwarding decisions based on UDP/TCP port numbers

Answer : the ability to make forwarding decisions based on IP addresses .the ability to make forwarding decisions based on UDP/TCP port numbers

In what mode does an LWAPP-enabled access point operate?


Options are :

  • autonomous mode
  • WGB
  • .lightweight mode
  • ad hoc mode

Answer : .lightweight mode

With RSTP hello timers set to the default interval, how quickly can a non-edge port discover that its neighbor is down?


Options are :

  • 10 seconds
  • .6 seconds
  • 5 seconds
  • .20 seconds

Answer : .6 seconds

200-105 Inter connecting Cisco Networking Devices Exam Set 3

What commands can be used to verify the trunking configuration of a router performing inter-VLAN routing? (Choose all that apply. Each correct answer is a complete solution.)


Options are :

  • router# show vtp status
  • router# show ip interface brief
  • .router# show vlans
  • .router# show ip route
  • router# show trunk

Answer : .router# show vlans .router# show ip route

What is the approximate amount of time it takes for a PortFast-enabled port to transition from blocking to forwarding?


Options are :

  • 30 seconds
  • Immediately
  • 20 seconds
  • 15 seconds

Answer : Immediately

When provisioning bandwidth for an IP telephony network, which elements are unique to an IP telephony call? (Choose two.)


Options are :

  • call-control signaling
  • routing protocol packets
  • speed of the segment to the telephone
  • .voice stream
  • IGMP packets

Answer : call-control signaling .voice stream

ICND1 100-105 Certification Practice Tests Set 1

In which VTP modes can you create and delete local VLANs? (Choose two.)


Options are :

  • Transparent
  • Client
  • Server
  • Host
  • User

Answer : Transparent Server

Which VTP mode and version should be configured on a switch so that its VLAN database can be separately maintained while it forwards all VTP advertisements it receives?


Options are :

  • .Client mode and version 2
  • Client mode and version 1
  • Transparent mode and version 2
  • .Server mode and version 2
  • Server mode and version 1

Answer : Transparent mode and version 2

You want to create a VTP domain named myvtpdomain and define this switch as one that can be configured with VLANs and advertises VLAN changes to other switches. What commands should you use? (Choose two.)


Options are :

  • switch(config)# vtp domain myvtpdomain
  • switch(config)# vtp server myvtpdomain
  • switch(config)# vtp mode server
  • switch(config)# vtp domain server

Answer : switch(config)# vtp domain myvtpdomain switch(config)# vtp mode server

Cisco CCNP Route 300-101 Practice Tests Set 3

You must add a new switch to the existing network using VTP to maintain the VLAN databases. Which mode should be configured on this switch so that VLANs can be separately maintained on this switch?


Options are :

  • Transparent
  • Server
  • None
  • .Client

Answer : Transparent

Which parameters are found in VTP advertisements? (Choose three.)


Options are :

  • Switch name
  • Management domain name
  • Password
  • .IP address
  • VTP mode
  • Revision number

Answer : Management domain name Password Revision number

How is a VLAN best described?


Options are :

  • collision domain
  • subne
  • broadcast domain
  • segment

Answer : broadcast domain

210-065 Implementing Cisco Video Network Devices Exam Set 4

Which of the following statements best describes the purpose of ARP with respect to CEF?


Options are :

  • ARP is used to build the adjacency table.
  • ARP is used to decrease the amount of time spent searching for an entry within a routing table.
  • ARP is used to reindex the routing table.
  • .ARP is used to build the FIB.

Answer : ARP is used to build the adjacency table.

In which VTP modes can you propagate VTP advertisements and create or delete local VLANs? (Choose two.)


Options are :

  • User
  • Transparent
  • .Server
  • Client
  • .Private

Answer : Transparent .Server

By default, which VLAN is the Cisco management VLAN?


Options are :

  • 1
  • 1005
  • 0
  • 1001

Answer : 1

ICND1 100-105 Certification Practice Tests Set 4

What command configures a port with a voice VLAN using 802.1Q?


Options are :

  • switch(config-if)# switchport voice vlan 10 dot1p
  • switch(config-if)# switchport voice vlan 10 q
  • .switch(config-if)# switchport voice vlan 10
  • switch(config-if)# switchport voice vlan 10 802.1q

Answer : .switch(config-if)# switchport voice vlan 10

Which redundancy mode for supervisor engine modules exhibits all of the following characteristics? Static routes are maintained during a switchover The Forwarding Information Base (FIB) is cleared during a switchover Dynamic route information is cleared during a switchover Route engine is initialized and switch modules are loaded


Options are :

  • RPR
  • RPR+
  • NSF
  • SSO

Answer : RPR+

Cisco 210-060 Implement Collaboration Device Practice Exam Set 4

Which of the following standards describes the details of RSTP?


Options are :

  • 802.1d
  • 802.1s
  • 802.1w
  • 802.1x

Answer : 802.1w

Which of the following commands configures a port with a VLAN?


Options are :

  • switchport mode access
  • vlan
  • switchport access vlan
  • vlan database

Answer : switchport access vlan

Which of the following statements best describes the result of issuing the instance 3 vlans 7 command?


Options are :

  • VLAN 7 is mapped to three MST instances.
  • VLAN 7 is mapped to MST instance 3.
  • VLAN 7 is mapped to switchport 3.
  • Seven VLANs are mapped to MST instance 3.

Answer : VLAN 7 is mapped to MST instance 3.

Cisco Data Center Architecture Set 5

Which characteristics apply to multilayer switching? (Choose three.)


Options are :

  • Provides Network-layer and Transport-layer access controls
  • Performs collision detection
  • Uses CPU-based packet forwarding
  • .Determines the forwarding path based on the Network layer address
  • .Provides isolation of the collision domain

Answer : Provides Network-layer and Transport-layer access controls .Determines the forwarding path based on the Network layer address .Provides isolation of the collision domain

What information is displayed by the command switch# show ip interface brief?


Options are :

  • a summary of the IP addresses on the interface and the interface's status
  • a summary of the IP addresses and subnet mask on the interface
  • the IP addresses for the interface and the routing protocol advertising the network
  • .the IP packet statistics for the interfaces

Answer : a summary of the IP addresses on the interface and the interface's status

Which Catalyst 6500 feature provides network-security enforcement based on Layer 2, Layer 3, and Layer 4 information on a VLAN?


Options are :

  • 802.1X
  • VACL
  • SPAN
  • NAM

Answer : VACL

300-320 Designing Cisco Network Service Architectures Exam Set 3

What IOS VLAN commands would create a new VLAN and assign it to a port? (Choose two.)


Options are :

  • switch(config)# vlan database 10
  • switch(config-if)# switchport vlan 10 enable
  • switch(config)# vlan 10
  • switch(config-if)# switchport access vlan 10

Answer : switch(config)# vlan 10 switch(config-if)# switchport access vlan 10

Which IOS command do you use to remove Layer 2 configurations and return an interface to Layer 3 mode?


Options are :

  • no vlan
  • vlan
  • no switchport
  • .switchport

Answer : no switchport

Which Cisco switch feature enables IP phones to be assigned IP addresses from a different subnet than the workstation attached to the same port?


Options are :

  • 802.1P
  • Auxiliary VLAN
  • in-line power
  • 802.1Q

Answer : Auxiliary VLAN

Cisco 210-060 Implement Collaboration Device Practice Exam Set 6

What attack technique attempts to fill a switching table so the attackers can capture traffic passing through a switch?


Options are :

  • .Rogue device
  • MAC flooding
  • MAC spoofing
  • VLAN hopping

Answer : MAC flooding

Which IOS commands should you enter in interface configuration mode to configure a switch port as an access port and assign it to VLAN 25? (Choose two.)


Options are :

  • vlan-membership static 25
  • switchport access vlan 25
  • switchport mode access
  • trunk on

Answer : switchport access vlan 25 switchport mode access

Which command do you use on a switch to put an interface that is in Layer 3 mode into Layer 2 mode?


Options are :

  • vlan
  • no switchport
  • .no vlan
  • .switchport

Answer : .switchport

200-125 Cisco Certified Network Associate (CCNA) Exam Set 2

Which of the following is true about CDP?


Options are :

  • .It is used to generate a MAC spoofing attack
  • .It is used to generate a denial of service attack
  • .It can be used as part of a MAC address flooding attack
  • It can be used to discover the network topology

Answer : It can be used to discover the network topology

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions