300-101 Implementing Cisco IP Routing (ROUTE) Practice Exam Set 1

Your company has a policy of creating all configurations in text files, checking the files, and then applying the configurations to the devices. Your assistant has presented you with the following partial configuration that she plans to execute on a router: interface S0/0/1 ipv6 address 2001:610:FFFF:1::1/64 ipv6 ospf 100 area 0 ipv6 router ospf 100 router-id 10.1.1.6 The configuration is supposed to accomplish the following: Enable IPv6 routing Assign a router ID Assign an IPv6 address to the interface Place the interface in OSPF area 0 Which step does this configuration NOT complete?


Options are :

  • Assign an IPv6 address to the interface
  • Enable IPv6 routing
  • Assign a router ID
  • .Place the interface in OSPF area 0

Answer : Enable IPv6 routing

300-101 Implementing Cisco IP Routing (ROUTE) Practice Exam Set 4

Which commands will display the feasible successors, the feasible distance, and the advertised distance for networks learned by a router?


Options are :

  • show bgp neighbors
  • .show ip eigrp traffic
  • .show ip eigrp topology
  • .show ip route

Answer : .show ip eigrp topology

Which method of advertising networks from an autonomous system into BGP can result in the most instability?


Options are :

  • Redistributing static routes into BGP
  • Redistributing static routes into IBGP
  • Using the network command
  • Redistributing dynamic routes into BGP

Answer : Redistributing dynamic routes into BGP

You have enabled RIPng on one of the interfaces of a router with the basic configuration. You have assigned an address to that interface using the ipv6 address command. Which of the following statements should appear in the output of the show running-config command executed on the router? (Choose all that apply.)


Options are :

  • ipv6 router rip
  • ipv6 unicast-routing
  • .ipv6 enable
  • ipv6 rip enable

Answer : ipv6 unicast-routing ipv6 rip enable

200-125 Cisco Certified Network Associate Practice Exam Set 12

Which show command displays entries in a router's Border Gateway Protocol (BGP) table?


Options are :

  • .show ip bgp topology
  • .show ip bgp summary
  • .show ip bgp table
  • .show ip bgp

Answer : .show ip bgp

Router10 is an area system border router (ASBR). The interfaces on Router 10 are configured as below: S 0/0 10.0.0.0/8 S0/1 172.16.0.0/8 Fa0/0 192.168.5.0/24 Fa0/1 192.168.6.0/24 You would like Router 10 to advertise the 192.168.5.0/24 and the 192.168.6.0/24 networks over OSPF in its Type 5 link-state advertisements (LSAs). What command set would instruct the router to do this?


Options are :

  • RTA10(config)# router ospf 1 RTA10(config)# redistribute connected
  • RTA10(config)# router ospf 1 RTA10(config-router)# redistribute connected
  • RTA10(config)# router ospf 1 RTA10(config-router)# redistribute static
  • RTA10(config)# router ospf 1 RTA10(config-router)# network 192.168.5.0 0.0.0.0 area 1 RTA10(config-router)# network 192.168.6.0 0.0.0.0 area 1

Answer : RTA10(config)# router ospf 1 RTA10(config-router)# redistribute connected

Which command can you use to verify that interfaces have been configured in the correct areas and to show timer intervals and neighbor adjacencies for OSPF?


Options are :

  • show ip ospf interface
  • show ip protocol
  • show ip ospf database
  • show ip ospf
  • show ip route

Answer : show ip ospf interface

200-125 Cisco Certified Network Associate Practice Exam Set 9

Which of the following commands would reveal the K values configured on an EIGRP router?


Options are :

  • show ip eigrp traffic
  • debug ip eigrp
  • debug eigrp packet
  • .show ip protocols

Answer : .show ip protocols

Which of the following does the show ip eigrp topology all-links command display?


Options are :

  • .Both feasible successors and non-feasible successors
  • Only non-feasible successors
  • .Only feasible successors
  • .Both successors and feasible successors

Answer : .Both feasible successors and non-feasible successors

Company A recently acquired Company B and the network infrastructures are being merged. Both organizations used non-overlapping globally unique network addressing but different Interior Gateway Protocols (IGPs). Initially, multiple WAN links will connect the two organizations. Company A will maintain its core routing protocol, and Company B's routing protocol will be the edge routing protocol. Two-way redistribution will be used to ensure full network routing capability. What additional routing configuration should be performed to prevent routing loops and suboptimal routing?


Options are :

  • Manually adjust the administrative distances.
  • Manually configure default routes.
  • Manually adjust the local preference attribute.
  • .Manually configure static routes.

Answer : Manually adjust the administrative distances.

100-105 Net Cert Interconnecting Cisco Networking Exam Set 6

Which of the following commands will enable the DHCP and relay services on a Cisco router?


Options are :

  • .RouterA(config)# dhcp enable
  • RouterA(config)# service dhcp
  • .RouterA(config)# enable dhcp
  • .RouterA(config-if)# dhcp enable

Answer : RouterA(config)# service dhcp

You have two autonomous systems connected by more than one ASBR. Which strategy does Cisco recommend in this situation?


Options are :

  • Manually configure routes in all ASBRs, and update the configuration each time there is a change in either AS.
  • Use a default route in both directions.
  • Allow routes to be exchanged in one direction, and use a default route in the other direction.
  • Use two-way redistribution.

Answer : Allow routes to be exchanged in one direction, and use a default route in the other direction.

You can use a variety of commands to verify and troubleshoot the operation of route redistribution on your network. Which command should you NOT use on routers that are overloaded?


Options are :

  • trace
  • show ipx route
  • .debug
  • show ip route

Answer : .debug

210-065 Implementing Cisco Video Network Devices Exam Set 2

Which EIGRP packet type is sent as a multicast when a new route is discovered, and sent as a unicast to synchronize topology tables when neighbors initialize?


Options are :

  • ACK
  • Update
  • Hello
  • Replies

Answer : Update

You instructed your assistant to configure load balancing on a router. The router currently has two routes to network A. One route has a cost of 15, and the other has a cost of 30. What command should the assistant execute to instruct the router to treat the two routes as equal without including any other routes in the load balancing?


Options are :

  • .routerA(config-router)# variance 3
  • .routerA(config)# variance 3
  • routerA(config-router)# variance 2
  • routerA(config)# variance 2

Answer : routerA(config-router)# variance 2

Which command is the proper command for allowing RIP routing updates to be received on an interface while not allowing them to be sent out of the same interface?


Options are :

  • Router(config-router)# passive-interface e0/0
  • Router(config)# passive-interface e0/0
  • .Router(config-if)# interface passive
  • Router(config-if)# passive-interface

Answer : Router(config-router)# passive-interface e0/0

210-260 Implementing Cisco Network Security Practice Exam Set 5

You need to resolve a route-selection problem in a redistributed network by increasing the administrative distance to several networks for a protocol, other than EIGRP or BGP, so that these routes will not be used. You create access list 5 to identify the relevant networks, and access the routing protocol configuration prompt. Which command will set the administrative distance to these networks to 220 for the selected protocol?


Options are :

  • .Router(config-router)# increase 0.0.0.0 255.255.255.255 admin 220 list 5
  • Router(config-router)# list 5 distance 220
  • Router(config-router)# admin 220 access-list 5
  • .Router(config-router)# distance 220 0.0.0.0 255.255.255.255 5

Answer : .Router(config-router)# distance 220 0.0.0.0 255.255.255.255 5

You manage the EIGRP subnet in your organization. You have enabled EIGRP for IPv6 on all the routers in the EIGRP AS 355 using the following commands on all the routers: The ipv6 unicast-routing command in global configuration mode The interface command in global configuration mode The ipv6 enable command in interface configuration mode The ipv6 eigrp command in interface configuration mode The ipv6 router eigrp command in global configuration mode The eigrp router-id command in global configuration mode During verification, you discover that EIGRP for IPv6 is not running on the routers. Which of the following should be done to fix the issue?


Options are :

  • The ipv6 address command should be executed in router configuration mode.
  • The eigrp router-id command should be executed in router configuration mode.
  • The eigrp router-id command should be executed in inte