200-105 Interconnecting Cisco Networking Devices Part Exam Set 7

Which Cisco IOS command would prompt for input in the following format? Protocol [ip]: Target IP address: 10.1.1.1 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 192.142.23.10 Type of service [0]:   Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort   


Options are :

  • ping
  • tracert
  • traceroute
  • ping 10.1.1.1

Answer : ping

Cisco 100-101 Interconnecting Cisco Networking Devices Exam Set 1

You have implemented SNMP v3 in your network. After making the configuration changes, you find that technicians in the TECHS group cannot access the MIB. You execute the show run command and receive the following output that relates to SNMP:   

<output omitted>

snmp-server group NORMAL v3 priv read NORMAL write NORMAL

snmp-server group TECHS v3 priv read TECHS access 99

snmp-server group TRAP v3 priv

!!

snmp-server user NORMAL NORMAL v3 auth sha CISCO priv des56 CISCO

snmp-server user TECHS TECHS v3 auth sha CISCO priv des56 CISCO

snmp-server user TRAP TRAP v3 auth sha CISCO priv des56 CISCO

snmp-server enable traps snmp linkup linkdown

snmp-server host 155.1.146.100 traps version 3 priv TRAP

What is preventing the TECHS group from viewing the MIB? 


Options are :

  • A mismatch between the authentication mechanism and the encryption type in the command creating the TECHS user
  • The absence of an access list defining the stations that can used by the TECHS group
  • The presence of the keyword auth in the command creating the TECHS user
  • The presence of the keyword priv in the command creating the RESTRICTED group

Answer : The absence of an access list defining the stations that can used by the TECHS group

Which switch will be selected as the root bridge by Spanning Tree Protocol (STP)? 


Options are :

  • switch with lowest Media Access Control (MAC) address
  • switch with lowest IP address
  • switch with lowest bridge ID
  • switch with lowest number of root ports

Answer : switch with lowest bridge ID

Which command enables HSRP on an interface? 


Options are :

  • hsrp
  • switchport mode hsrp
  • standby ip
  • standby mode hsrp

Answer : standby ip

200-125 Cisco Certified Network Associate Practice Exam Set 10

Which of the following statements are TRUE regarding EIGRP operation? (Choose two.)

A. A successor is a backup route, and is installed in both the routing and topology tables.

B. A successor is a primary route, and is installed in both the routing and topology tables.

C. A successor is a primary route, and is installed only in the routing table.

D. A feasible successor is a backup route, and is installed in both the routing and topology tables.

E. A feasible successor is a primary route, and is only installed in the routing table.

F. A feasible successor is a backup route, and is only installed in the topology table.

G. If the successor route fails and no feasible successor route exists, the router will send an update with the route marked with an unreachable metric of 16. 


Options are :

  • C,D
  • E,G
  • A,B
  • B,F

Answer : B,F

Which of the following is NOT true of the Cisco APIC-EM? 


Options are :

  • It is appropriate for the data center environment
  • It provides network topology visualization
  • It can verify the operation of access lists
  • It can perform identity tracking

Answer : It is appropriate for the data center environment

Which of the following protocols is responsible for negotiating upper-layer protocols that will be carried across a Point-to-Point Protocol (PPP) connection? 


Options are :

  • LCP
  • NCP
  • LMI
  • ISDN

Answer : NCP

300-320 Designing Cisco Network Service Architectures Exam Set 2

You are the Cisco administrator for NationalAct Incorporated. One of your assistants is preparing to introduce a new switch to the network. Before doing so, you execute the show vtp status command on OldSwitch and NewSwitch, respectively, and receive the following output: OldSwitch# show vtp status VTP Version : 2 Configuration Revision : 62 Maximum VLANs supported locally : 1005 Number of existing VLANs : 24 VTP Operating Mode : Server VTP Domain Name : Corporate VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled <<output omitted>>

NewSwitch# show vtp status VTP Version : 2 Configuration Revision : 125 Maximum VLANs supported locally : 1005 Number of existing VLANs : 10 VTP Operating Mode : Server  VTP Domain Name : Corporate VTP Pruning Mode : Enabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled <<output omitted>>

If NewSwitch is introduced to the network, which of the following will be true? 


Options are :

  • OldSwitch will retain its current VTP data.
  • NewSwitch will delete its current VTP data.
  • There will be 10 VLANs in the network.
  • There will be 24 VLANs in the network.

Answer : There will be 10 VLANs in the network.

You are planning the configuration of an IPsec-protected connection between two routers. You are concerned only with the integrity of the data that passes between the routers. You are less concerned with the confidentiality of the data, and you would like to minimize the effect of IPsec on the data throughput 

Which protocol option should you choose? 


Options are :

  • Encapsulating Security Payload (ESP) in transport mode
  • Encapsulating Security Payload (ESP) in tunnel mode
  • Authentication Header (AH) in tunnel mode
  • Authentication Header (AH) in transport mode

Answer : Authentication Header (AH) in tunnel mode

Which of the following is a classful routing protocol?   


Options are :

  • BGPv4
  • RIPv1
  • RIPv2
  • EIGRP

Answer : RIPv1

300-101 Implementing Cisco IP Routing (ROUTE) Practice Exam Set 1

Which of the following commands would instruct OSPF to advertise ONLY the 192.168.10.0/24 network in Area 0? 


Options are :

  • Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 255.255.255.0 area 0
  • Router(config)# router ospf 1 Router(config-router)# network 192.168.11.0 0.0.0.255 area 0
  • Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
  • Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 0.0.255.255 area 0

Answer : Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 0.0.0.255 area 0

When the auth keyword is used in the snmp-server host command, which of the following must be configured with an authentication mechanism? 


Options are :

  • the interface
  • the group
  • the user
  • the host

Answer : the user

What port types are available for Rapid Spanning Tree Protocol (RSTP) but NOT available in Spanning Tree Protocol (STP)? (Choose two.)

A. Root port

B. Backup port

C. Alternate port

D. Designated port

E. Learning port 


Options are :

  • B,C
  • A,B
  • D,E
  • C,D

Answer : B,C

200-125 Cisco Certified Network Associate Practice Exam Set 8

Which of the following commands will set the line speed of a serial connection that connects to a Channel Service Unit /Digital Service Unit (CSU/DSU) at 56 Kbps? 


Options are :

  • service-module 56k clock rate speed
  • bandwidth 56000
  • service-module 56000 clock rate speed
  • bandwidth 56k

Answer : service-module 56k clock rate speed

You set up several routers in your lab. Two of them are connected back to back using Data Terminal Equipment (DTE)-to-Data Circuit-terminating Equipment (DCE) cable. You need to configure the clock rate. On which router would you configure the clock rate? 


Options are :

  • The clock rate cannot be configured
  • The clock rate is set by default
  • the DTE
  • the DCE

Answer : the DCE

What Cisco Catalyst switch feature can be used to define ports as trusted for DHCP server connections? 


Options are :

  • private VLANs
  • port security
  • DHCP snooping
  • 802.1x

Answer : DHCP snooping

200-105 Inter connecting Cisco Networking Devices Exam Set 2

What is the significance of the 1 in the following configuration?   router(config)# router eigrp 1 


Options are :

  • It is the AS number for EIGRP and is locally significant to this router.
  • It is the AS number for EIGRP and must be the same on all EIGRP routers.
  • It is the process ID for EIGRP and must be the same on all EIGRP routers.
  • It is the process ID for EIGRP and is locally significant to this router

Answer : It is the AS number for EIGRP and must be the same on all EIGRP routers.

Which technique is used to stop routing loops by preventing route update information from being sent back over the interface on which it arrived?   


Options are :

  • Route poisoning
  • Triggered updates
  • Split horizon
  • Holddown timer

Answer : Split horizon

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions