200-105 Interconnecting Cisco Networking Devices Part Exam Set 6

What command should you use to quickly view the HSRP state of the switch for all HSRP groups of which the switch is a member?   


Options are :

  • switch# show standby brief
  • switch# show ip interface brief
  • switch# show standby
  • switch# show hsrp

Answer : switch# show standby brief

400-101 CCIE Routing and Switching Written Practice Exam Set 9

What command would be used to verify trusted DHCP ports? 


Options are :

  • show ip arp trust
  • show ip trust
  • show ip dhcp snooping
  • show mls qos

Answer : show ip dhcp snooping

You are discovering that there are differences between the configuration of EIGRP for IPv6 and EIGRP for IPv4. Which statement is true with regard to the difference? 


Options are :

  • AS numbers are not required in EIGRP for IPv4
  • A router ID is required for both versions
  • AS numbers are not required in EIGRP for IPv6
  • A router ID must be configured under the routing process for EIGRP for IPv4

Answer : A router ID is required for both versions

On Cisco switches, what is the correct order of port transition through the Spanning Tree Protocol (STP) states? 


Options are :

  • learning, listening, blocking, forwarding
  • listening, blocking, forwarding, learning
  • blocking, listening, learning, forwarding
  • blocking, learning, forwarding, listening

Answer : blocking, listening, learning, forwarding

200-125 Cisco Certified Network Associate Practice Exam Set 2

Which of the following is NOT true of APIC-EM? 


Options are :

  • It provides a single point for network automation
  • It is open and programmable
  • It supports greenfield but not brownfield deployments
  • It saves time and cost

Answer : It supports greenfield but not brownfield deployments

Which of the following is NOT a packet type used by Enhanced Interior Gateway Routing Protocol (EIGRP)?   


Options are :

  • Query
  • Reply
  • Response
  • Ack

Answer : Response

Refer to the following sample output: *: interface is up  IHQ: pkts in input hold queue IQD: pkts dropped from input queue OHQ: pkts in output hold queue OQD: pkts dropped from output queue RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec) TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec) TRTL: throttle count Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL ---------------------------------------------------------------------- * FastEthernet0/0 0 0 0 0 0 0 0 0 0 Serial0/0 0 0 0 0 0 0 0 0 0 FastEthernet0/1 0 0 0 0 0 0 0 0 0 Serial0/1 0 0 0 0 0 0 0 0 0 Which Cisco Internetwork Operating System (IOS) command produces this output?   


Options are :

  • show interfaces serial fast-ethernet
  • show interfaces
  • show interfaces summary
  • show interfaces fast-ethernet 0/0

Answer : show interfaces summary

400-101 CCIE Routing and Switching Written Practice Exam Set 5

Which of the following TCP port numbers is used by Simple Mail Transfer Protocol (SMTP)?   


Options are :

  • 25
  • 21
  • 57
  • 23

Answer : 25

Which metric does the Open Shortest Path First (OSPF) routing protocol use for optimal path calculation? 


Options are :

  • Delay
  • MTU
  • Cost
  • Hop count

Answer : Cost

Which Cisco Internetwork Operating System (IOS) command is used to view the number of Enhanced Interior Gateway Routing Protocol (EIGRP) packets that are sent and received? 


Options are :

  • show eigrp neighbors
  • show ip eigrp interfaces
  • show ip eigrp packets
  • show ip eigrp traffic

Answer : show ip eigrp traffic

200-105 Inter connecting Cisco Networking Devices Exam Set 2

Which of the following is NOT managed by the cloud provider in an IaaS deployment? 


Options are :

  • operating system
  • virtualization
  • storage
  • servers

Answer : operating system

Which of the following statements is true with regard to SDN? 


Options are :

  • It implements the control plane as software
  • It combines the control plane and the data plane
  • It separates the data plane and the forwarding plan
  • It implements the data plane as software

Answer : It implements the control plane as software

You instructed your assistant to add a new router to the network. The routers in your network run OSPF. The existing router, OldRouter, is configured as follows: router ospf 1 network 192.168.5.0 0.0.0.255 area 0 network 192.168.10.0 0.0.0.255 area 0 The OldRouter interface that connects to NewRouter is 192.168.5.3/24. Your assistant shows you the configuration that will be implemented: newrouter(config)# router ospf 1 newrouter(config-router)# network 192.168.5.0 255.255.255.0 area 0 What is wrong with this configuration?   


Options are :

  • The process ID number is incorrectly configured.
  • The network statement is incorrectly configured.
  • The area ID is incorrectly configured.
  • The wildcard mask is incorrectly configured.

Answer : The wildcard mask is incorrectly configured.

400-101 CCIE Routing and Switching Written Practice Exam Set 6

Which redundancy mode for supervisor engine modules exhibits all of the following characteristics?

- Static routes are maintained during a switchover

- The Forwarding Information Base (FIB) is cleared during a switchover

- Dynamic route information is cleared during a switchover

- Route engine is initialized and switch modules are loaded   


Options are :

  • RPR
  • RPR+
  • SSO
  • NSF

Answer : RPR+

What command can be used on a Cisco switch to display the virtual MAC address for the HSRP groups of which the switch is a member? 


Options are :

  • switch# show standby
  • switch# show hsrp mac
  • switch# show standby mac
  • switch# show standby brief

Answer : switch# show standby

You have two routers in your OSPF area 0. Router 1 is connected to Router 2 via its Serial 1 interface, and to your ISP via the Serial 0 interface. Router 1 is an ASBR. After your assistant configures a default route on Router 1, you discover that whenever either router receives packets destined for networks that are not in the routing tables, it causes traffic loops between the two routers. To troubleshoot, you execute the show run command on Router 1. Part of the output is shown below: <output omitted>

IP route 0.0.0.0 0.0.0.0 serial 1 Router ospf 1 Network 192.168.5.0 0.0.0.255 area 0 Default-information originate

Which command or set of commands should you execute on Router 1 to stop the looping traffic while maintaining Router 2's ability to send traffic to the Internet? 


Options are :

  • Execute the default-information originate always command.
  • Execute the no default-information originate command.
  • Execute the no ip route 0.0.0.0 0.0.0.0 serial 1 command and then execute the ip route 0.0.0.0 0.0.0.0 serial 0 command.
  • Execute the no network 192.168.5.0 area 0 command and then execute the network 192.168.5.0 255.255.255.0 area 0 command.

Answer : Execute the no ip route 0.0.0.0 0.0.0.0 serial 1 command and then execute the ip route 0.0.0.0 0.0.0.0 serial 0 command.

100-105 Net Cert Interconnecting Cisco Networking Exam Set 2

Which of the following statements describes split horizon? 


Options are :

  • For a period of time, the router will ignore any route advertisements with a lower metric to a downed route.
  • The moment a router determines a route has gone down, it will immediately send a route update with an infinite metric to that route.
  • The router learns from its neighbor that a route has gone down, and the router sends an update back to the neighbor with an infinite metric to that route.
  • A router will not send route information back out the same interface over which it was learned

Answer : A router will not send route information back out the same interface over which it was learned

You are configuring SPAN so you can connect a sniffer to your switch. Which of the following is NOT true with regard to the source port in the configuration? 


Options are :

  • It can monitor both ingress and egress traffic
  • It can also be the destination port
  • It can be monitored in multiple SPAN sessions
  • It can be an EtherChannel

Answer : It can also be the destination port

Which of the following is NOT a benefit of cloud computing to cloud users?   


Options are :

  • Highly available, horizontally scaled applications
  • Centralized appearance of resources
  • Cost reduction from standardization and automation
  • On-demand self-service resources provisioning

Answer : Cost reduction from standardization and automation

642-732 Conducting Cisco Unified Wireless Site Survey Exam Set 1

Which WAN switching technology is used by Asynchronous Transfer Mode (ATM)? 


Options are :

  • packet switching
  • cell-switching
  • virtual switching
  • circuit-switching

Answer : cell-switching

Which of the following commands configures an SNMP host to authenticate a user by username and send clear text notifications, the receipt of which will be acknowledged by the receiver? 


Options are :

  • Router(config)# snmp-server host 192.168.5.5 informs version 3 noauth public
  • Router(config)# snmp-server host 192.168.5.5 traps version 3 auth public
  • Router(config)# snmp-server host 192.168.5.5 informs version 2c public
  • None
  • Router(config)# snmp-server host 192.168.5.5 informs version 3 authpriv public

Answer : Router(config)# snmp-server host 192.168.5.5 informs version 3 noauth public

The following is a partial output of the show interfaces command: Serial 0 is up, line protocol is down Hardware is MCI Ethernet, address is 0000.0c00.750c (bia 0000.0c00.750c) Internet address is 134.108.28.8, subnet mask is 255.255.255.0  MTU 1500 bytes, BW 10000 Kbit, DLY 100000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 4:00:00 Last input 0:00:00, output 0:00:00, output hang never Last clearing of "show interface" counters 0:00:00 Output queue 0/40, 0 drops; input queue 0/75, 0 drops Five minute input rate 0 bits/sec, 0 packets/sec Five minute output rate 2000 bits/sec, 4 packets/sec 1127576 packets input, 447251251 bytes, 0 no buffer Received 354125 broadcasts, 0 runts, 0 giants, 57186* throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 5332142 packets output, 496316039 bytes, 0 underruns 0 output errors, 432 collisions, 0 interface resets, 0 restarts <<output omitted>>

What does the Serial 0 is up, line protocol is down statement signify in the output? (Choose all that apply.)

A. the shutdown interface command is present in the router configuration

B. a cable is unplugged

C. the interface is displaying normal operation

D. there are no problems with physical connectivity

E. there is a configuration problem in the local or remote router 


Options are :

  • D,E
  • A,B
  • A,C
  • C,D

Answer : D,E

300-320 Designing Cisco Network Service Architectures Exam Set 2

Which of the following is NOT a true statement regarding Virtual Private Networks (VPNs)? 


Options are :

  • A VPN is a method of securing private data over public networks
  • IPsec provides packet-level encryption
  • IPsec is a method for providing security over VPN
  • Frame Relay is a Layer 3 VPN technology

Answer : Frame Relay is a Layer 3 VPN technology

Which command is NOT mandatory for inclusion in a plan to implement IP Service Level Agreements (SLAs) to monitor IP connections and traffic? 


Options are :

  • ip sla
  • ip sla schedule
  • icmp-echo
  • ip sla reset

Answer : ip sla reset

Which of the following technologies allows a switch port to immediately transition to a forwarding state?   


Options are :

  • CDP
  • VTP
  • Rapid STP
  • PortFast

Answer : PortFast

200-125 Cisco Certified Network Associate Practice Exam Set 2

Which of the following are classless routing protocols? (Choose four.)

A. Open Shortest Path First (OSPF)

B. Enhanced Interior Gateway Routing Protocol (EIGRP)

C. Interior Gateway Routing Protocol (IGRP)

D. Routing Information Protocol version 1 (RIPv1)

E. Border Gateway Protocol (BGP)

F. Routing Information Protocol version 2 (RIPv2) 


Options are :

  • A,C,D,F
  • A,C,D,E
  • C,D,E,F
  • A,B,E,F

Answer : A,B,E,F

Which of the following statements is NOT true of Cisco ACI?   


Options are :

  • It decreases network visibility.
  • It provides policy driven automation support.
  • It uses Cisco APIC as the central management system.
  • It is a comprehensive SDN architecture.

Answer : It decreases network visibility.

Your network consists of one HSRP group of six routers. All of the routers are functioning properly. The network has been stable for several days. In which HSRP state are most of the routers? 


Options are :

  • Standby
  • Active
  • Learn
  • Listen

Answer : Listen

200-105 Interconnecting Cisco Networking Devices Part Exam Set 4

You run the following command: switch# show ip interface brief What information is displayed? 


Options are :

  • The IP addresses for the interface and the routing protocol advertising the network
  • A summary of the IP addresses on the interface and the interface's status
  • The IP packet statistics for the interfaces
  • A summary of the IP addresses and subnet mask on the interface

Answer : A summary of the IP addresses on the interface and the interface's status

How is the designated router (DR) determined by OSPF on a multi-access network segment? 


Options are :

  • The lowest interface priority, then the highest OSPF process ID
  • The highest interface priority, then the highest RID
  • The highest interface priority, then the highest OSPF process ID
  • The lowest interface priority, then the highest RID

Answer : The highest interface priority, then the highest RID

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions