200-105 Interconnecting Cisco Networking Devices Part Exam Set 1

On which of the following networks will OSPF elect a designated router (DR)? (Choose two.)

A. Broadcast

B. NBMA

C. Point-to-point

D. Point-to-multi point   


Options are :

  • B,D
  • A,B
  • A,C
  • C,D

Answer : A,B

100-105 Net Cert Interconnecting Cisco Networking Exam Set 5

You manage the EIGRP subnet in your organization. You have enabled EIGRP for IPv6 on all the routers in the EIGRP AS 260 using the following commands on all the routers: \

The ipv6 unicast-routing command in global configuration mode

The interface command in global configuration mode

The ipv6 enable command in interface configuration mode

The ipv6 eigrp command in interface configuration mode

The ipv6 router eigrp command in global configuration mode

The eigrp router-id command in global configuration mode

During verification, you discover that EIGRP for IPv6 is not running on the routers. Which of the following should be done to fix the issue?   


Options are :

  • The eigrp router-id command should be executed in router configuration mode
  • The ipv6 address command should be executed in interface configuration mode.
  • The ipv6 address command should be executed in router configuration mode.
  • The eigrp router-id command should be executed in interface configuration mode.

Answer : The eigrp router-id command should be executed in router configuration mode

Which of the following is NOT a feature offered by Enhanced Interior Gateway Routing Protocol (EIGRP)? 


Options are :

  • variable length subnet masks (VLSM)
  • neighbor discovery mechanism
  • multiple vendor compatibility
  • partial updates

Answer : multiple vendor compatibility

You are troubleshooting a problem with two routers configured in a HSRP group. You intended to configure the routers so that Router A and Router B would each track their respective Fa0/1 interfaces and decrement their priorities for several VLAN groups if the tracked interface went down. However, you find that Router A is not taking over as the active device for the HSRP group on VLAN 101 when the Fa0/1 interface on Router B fails. Which command would NOT be useful for discovering the problem? 


Options are :

  • show vlans
  • show standby brief
  • show running-configuration
  • show standby

Answer : show vlans

Cisco 100-101 Interconnecting Cisco Networking Devices Exam Set 2

What is the significance of the following BECN packet statistics? Router# show frame-relay pvc 16 PVC Statistics for interface serial0 (Frame Relay DTE) DLCI = 16, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in FECN pkts 0 in BECN pkts 100 out FECN pkts 0 out BECN pkts 0  <<output omitted>>



Options are :

  • The Frame Relay mapping table is corrupt
  • The Frame Relay mapping table is missing an entry.
  • The router is experiencing congestion in receiving frames.
  • The router is experiencing congestion in sending frames.

Answer : The router is experiencing congestion in sending frames.

You are the network administrator for your company. You want to implement a routing protocol that can support hierarchical routing, multiple vendor environments, and authentication, and provides fast convergence. Which routing protocol will you implement?   


Options are :

  • Routing Information Protocol version 2 (RIPv2)
  • Interior Gateway Routing Protocol (IGRP)
  • Enhanced Interior Gateway Routing Protocol (EIGRP)
  • Open Shortest Path First (OSPF)

Answer : Open Shortest Path First (OSPF)

You just finished configuring VLAN Trunking Protocol (VTP) in a network containing five switches. One of the switches is not receiving VLAN information from the switch that is acting as the server. Which of the following could NOT be a reason why the switch is not receiving the information? 


Options are :

  • The VTP password may be misspelled on the switch
  • The VTP domain name on the switch may be misspelled
  • The configuration revision number may be out of sync
  • The VTP version used on the switch may be different

Answer : The configuration revision number may be out of sync

Cisco 100-101 Interconnecting Cisco Networking Devices Exam Set 1

You and your team are evaluating the use of OSPFv3 in your IPv6 network. Which of the following statements is true of OSPFv3?  


Options are :

  • Router IDs must match for adjacency formation
  • Area types do not need to match for adjacency formation
  • There will be a higher demand on the processor to run the link-state routing algorithm
  • Area IDs do not need to match for adjacency formation

Answer : There will be a higher demand on the processor to run the link-state routing algorithm

You network team is exploring the use of switch staking. Which of the following statements is NOT true of switch stacking? 


Options are :

  • The master switch is the only switch with full access to the interconnect bandwidth
  • Up to nine switches can be added to the stack
  • The stack has a single IP address
  • Switches are connected with special cable

Answer : The master switch is the only switch with full access to the interconnect bandwidth

You know that Router2 is configured for RIP. Which Cisco Inter network Operating System (IOS) command is used to view the current state of all active routing protocols? 


Options are :

  • show ip routing process
  • show ip arp
  • show ip protocols
  • debug ip rip

Answer : show ip protocols

Cisco CCNP Route 300-101 Practice Tests Set 5

You receive the following error message after addressing and enabling an interface: %192.168.16.0 overlaps with FastEthernet0/0 Which two are NOT the causes of the error message? (Choose two.)

A. incorrect subnet mask in the new interface

B. incorrect IP address on the new interface

C. incorrect encapsulation configured

D. failure to issue the no shutdown command 


Options are :

  • B,D
  • A,B
  • A,C
  • C,D

Answer : C,D

Which Cisco Inter network Operating System (IOS) command is used to view the VLAN Trunking Protocol (VTP) statistics information? 


Options are :

  • show vtp domain
  • show vtp counters
  • NONE
  • show vtp statistics
  • show vtp status

Answer : show vtp counters

Given the following output, which statements can be determined to be true? (Choose three.)

RouterA2# show ip ospf neighbor

Neighbor ID Pri State Dead Time Address Interface

192.168.23.2 1 FULL/BDR 00:00:29 10.24.4.2 FastEthernet1/0

192.168.45.2 2 FULL/BDR 00:00:24 10.1.0.5 FastEthernet0/0

192.168.85.1 1 FULL/- 00:00:33 10.6.4.10 Serial0/1

192.168.90.3 1 FULL/DR 00:00:32 10.5.5.2 FastEthernet0/1

192.168.67.3 1 FULL/DR 00:00:20 10.4.9.20 FastEthernet0/2

192.168.90.1 1 FULL/BDR 00:00:23 10.5.5.4 FastEthernet0/1 

<<output omitted>>

A. This router is the DR for subnet 10.1.0.0 

B. The DR for the network connected to Fa0/0 has an interface priority greater than 2.

C. The DR for the network connected to Fa0/1 has a router ID of 10.5.5.2.

D. The DR for the serial subnet is 192.168.85.1.

E. This router is neither the DR nor the BDR for the Fa0/1 subnet.

F. RouterA2 is connected to more than one multi-access network


Options are :

  • A,D,E
  • C,D,E
  • B,E,F
  • A,B,C

Answer : B,E,F

200-105 Interconnecting Cisco Networking Devices Part Exam Set 4

Which of the following technologies should be used to prevent a switching loop if a switch is connected to a port configured for Port Fast? 


Options are :

  • Root Guard
  • BPDU Guard
  • RSTP
  • PVST

Answer : BPDU Guard

Which Cisco Inter network Operating System (IOS) command is used to view information about Open Shortest Path First (OSPF) routing processes?   


Options are :

  • show ip ospf database
  • show ip ospf statistics
  • show ip ospf
  • show ip ospf traffic

Answer : show ip ospf

How is load balancing achieved when implementing HSRP?   


Options are :

  • By configuring multiple gateways on the routers
  • By configuring the same priority on all HSRP group members
  • By configuring multiple virtual router addresses
  • By using multiple HSRP groups

Answer : By using multiple HSRP groups

Cisco 210-060 Implement Collaboration Device Practice Exam Set 1

What is the default Administrative Distance (AD) value for an Enhanced Interior Gateway Routing Protocol (EIGRP) summary route? 


Options are :

  • 5
  • 1
  • 90
  • 20

Answer : 5

You are configuring a serial link between a Cisco router and a router produced by another vendor. What would be the advantages of using Point to Point Protocol (PPP) over High Level Data Link Control (HDLC) in this scenario? 


Options are :

  • PPP is faster.
  • PPP performs error checking.
  • HDLC has a proprietary "type" field that may be incompatible with equipment from other vendors.
  • HDLC is not available on non-Cisco routers.

Answer : HDLC has a proprietary "type" field that may be incompatible with equipment from other vendors.

When executed on a HSRP group member named Router 10, what effect does the following command have? Router10(config-if)# standby group 1 track serial0 25 


Options are :

  • It will cause the router to increase its HSRP priority by 25 if the Serial0 interface on the standby router goes down
  • It will cause the router to decrement its HSRP priority by 25 if Serial 0 goes down
  • It will cause the router to notify Router 25 is serial 0 goes down
  • It will cause the router to shut down the Serial0 interface if 25 packets have been dropped

Answer : It will cause the router to decrement its HSRP priority by 25 if Serial 0 goes down

300-115 Implementing Cisco IP Switched Network Practice Exam Set 1

You are advising a client on the options available to connect a small office to an ISP. Which of the following is an advantage of using an ADSL line? 


Options are :

  • it uses the existing phone line
  • it uses the existing cable TV connection
  • you receive a committed information rate (CIR) from the provider
  • the upload rate is as good as the download rate

Answer : it uses the existing phone line

You execute the ping command from a host, but the router does not have a path to its destination. Which of the following ICMP message types will a client receive from the router? 


Options are :

  • ICMP destination unreachable
  • ICMP time exceeded
  • ICMP echo-reply
  • ICMP redirect

Answer : ICMP destination unreachable

Which of the following commands would instruct OSPF to advertise ONLY the 192.168.10.0/24 network in Area 0? 


Options are :

  • Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
  • Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 0.0.255.255 area 0
  • Router(config)# router ospf 1Router(config-router)# network 192.168.11.0 0.0.0.255 area 0
  • Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 255.255.255.0 area 0

Answer : Router(config)# router ospf 1Router(config-router)# network 192.168.10.0 0.0.0.255 area 0

200-310 Designing for Cisco Inter network Solutions Exam Set 5

Which of the following techniques is NOT used by distance vector protocols to stop routing loops in a network?   


Options are :

  • Holddowns
  • Route poisoning
  • None of the Above
  • Spanning Tree Protocol (STP)
  • Split horizon

Answer : Spanning Tree Protocol (STP)

Which type of connector is used for an Integrated Services Digital Network Basic Rate Interface (ISDN BRI) connection? 


Options are :

  • Console
  • RJ-45
  • DB-60
  • AUI

Answer : RJ-45

Which commands would be used to enable Enhanced Interior Gateway Routing Protocol (EIGRP) on a router, and configure the IP addresses 10.2.2.2 and 192.168.1.1 as a part of complete EIGRP configuration? (Choose three.)

A. router eigrp 10

B. router eigrp

C. network 10.2.2.2

D. network 10.0.0.0

E. network 192.168.1.0

F. network 192.168.1.1   


Options are :

  • A,B,C
  • C,D,F
  • B,C,D
  • A,D,E

Answer : A,D,E

642-732 Conducting Cisco Unified Wireless Site Survey Exam Set 4

You want to encrypt and transmit data between peer routers with high confidentiality. Which protocol option should you choose? 


Options are :

  • Authentication Header (AH) in transport mode
  • Encapsulating Security Payload (ESP) in tunnel mode
  • Authentication Header (AH) in tunnel mode
  • Encapsulating Security Payload (ESP) in transport mode

Answer : Encapsulating Security Payload (ESP) in tunnel mode

What two devices can be connected to a router WAN serial interface that can provide clocking? (Choose two.) 

A. CSU/DSU

B. switch

C. modem

D. hub 


Options are :

  • B,D
  • A,B
  • A,C
  • C,D

Answer : A,C

Which of the following is NOT a possible component of Enhanced Interior Gateway Routing Protocol's (EIGRP) composite metric? 


Options are :

  • Bandwidth
  • Cost
  • Load
  • Delay

Answer : Cost

Cisco 210-060 Implement Collaboration Device Practice Exam Set 1

You are the network administrator for your company. Your company has opened a new site in London. The Chief Technical Officer (CTO) of the company wants to implement a routing protocol that can provide the following features:

- Supports multiple large networks

- Does not require a hierarchical physical topology

- Supports VLSM

- Provides loop prevention and fast convergence

- Provides load balancing over un-equal cost links

Which routing protocol should be implemented in the new site? 


Options are :

  • Interior Gateway Routing Protocol (IGRP)
  • Open Shortest Path First (OSPF)
  • Enhanced Interior Gateway Routing Protocol (EIGRP)
  • Routing Information Protocol version 2 (RIPv2)

Answer : Enhanced Interior Gateway Routing Protocol (EIGRP)

You are implementing IP SLA and would like to use it to measure hop-by-hop response time between a Cisco router and any IP device on the network. Which of the following IP SLA operations would you use for this? 


Options are :

  • ICMP path echo operation
  • Internet Control Message Protocol Echo Operation
  • UDP Jitter Operation for VoIP
  • UDP Jitter Operation

Answer : ICMP path echo operation

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions