400-101 CCIE Routing and Switching Written Practice Exam Set 2

What are the first three criteria used by the BGP router determines the best route to your destination? (Choose the best answer.)


Options are :

  • .highest local preference, the shortest AS path, the highest weight
  • None
  • MED lowest and the highest weight, the highest local preference
  • Maximum weight, the shortest AS path, the lowest MED
  • Maximum load, the highest local preference locally from the paths

Answer :Maximum load, the highest local preference locally from the paths

400-101 CCIE Routing and Switching Written Practice Exam Set 6

Which of the following statements is correct regarding traffic shaping? (Select two options.)


Options are :

  • traffic shaping is not smooth traffic.
  • Traffic Shaping use the leaky bucket to smooth traffic.
  • Traffic shaping is applied only incoming traffic.
  • .Traffic shaping buffers too much traffic.
  • Traffic shaping drops or comments to excessive traffic

Answer :Traffic Shaping use the leaky bucket to smooth traffic. .Traffic shaping buffers too much traffic.

Which of the following LSA flooding information to all other routers is a multi-use systems segment? (Choose the best answer.)


Options are :

  • all routers area
  • None
  • only BDR
  • .Only DR
  • DR and BDR

Answer :.Only DR

Another system administrator has configured NetFlow your corporate network. You want to make sure that the Fast Ethernet 0/0 interface Router is used to monitor inbound flows. Which of the following commands should be given? (Choose the best answer.)


Options are :

  • show flow exporter
  • .Show ip flow interface
  • Performing flow probe
  • show ip flow export
  • None

Answer :.Show ip flow interface

400-101 CCIE Routing and Switching Written Practice Exam Set 4

Which of the following IPv6 prefixes used for multicast addresses? (Choose the best answer.)


Options are :

  • FE80 :: / 10
  • FF00 :: / 8
  • 2000 :: / 3
  • FD00 :: / 8
  • FC00 :: / 8

Answer :FF00 :: / 8

between the two switches is LACP Etherchannel bundle. Every first criteria in order to determine which ports are activated? (Choose the best answer.)


Options are :

  • .the port priority for each switch port
  • None
  • the port number for each switch port
  • The MAC address of each switch
  • the system priority for each switch

Answer :the system priority for each switch

Which of the following are the protocols used to control the level? (Select two options.)


Options are :

  • EIGRP and OSPF
  • HTTP, HTTPS, and SNMP
  • TDP and LDP
  • SSH and Telnet
  • FIB and LFIB

Answer :EIGRP and OSPF TDP and LDP

400-101 CCIE Routing and Switching Written Practice Exam Set 5

Which of the following does a router consider when measuring the defendant's processing IP SLA operation? (Choose the best answer.)


Options are :

  • .ICMP one-way travel time from the defendant to the transmitter
  • ICMP one-way travel time from the transmitter-responder
  • responder interface
  • ICMP round-trip travel time
  • responder packet timestamps

Answer :responder packet timestamps

Which of the following statements is true about DiffServ class AF41? (Choose the best answer.)


Options are :

  • AF41 is a low priority and high drop probability.
  • AF41 is a high priority, and the probability of a large drop.
  • None
  • AF41 has a low priority and low drop probability.
  • AF41 is a high-priority and low-drop probability.

Answer :AF41 is a high-priority and low-drop probability.

Te following commands router: line console 0 exec-timeout January 30 How long a console session to the router set up without further input before the session is automatically disconnected? (Choose the best answer.)


Options are :

  • 30 minutes
  • 30 seconds
  • 90 seconds
  • 60 seconds

Answer :90 seconds

400-101 CCIE Routing and Switching Written Practice Exam Set 5

Which of the following commands to effectively prevent the STP port? (Choose the best answer.)


Options are :

  • None
  • spanning-tree guard loop
  • spanning-tree bpduguard use
  • spanning-tree bpdufilter use
  • spanning-tree guard root

Answer :spanning-tree bpdufilter use

Which of the following is true regarding the VRRP? (Choose the best answer.)


Options are :

  • VRRP allows simultaneous operation of a plurality of gateway routers.
  • VRRP is a virtual gateway, and a number of active virtual forwarder.
  • .VRRP has one active router and a second router in the standby mode.
  • None
  • VRRP is a single master virtual router and multiple backup virtual routers

Answer :VRRP is a single master virtual router and multiple backup virtual routers

Which of the following information does not include type 2 LSA? (Choose the best answer.)


Options are :

  • External routes are redistributed to OSPF
  • the subnet information for the entire region
  • None
  • the router ID and IP addresses to a single router
  • .subnet and router information for all the routers segment

Answer :.subnet and router information for all the routers segment

400-101 CCIE Routing and Switching Written Practice Exam Set 8

Which of the following statements is true about how EIGRP and OSPF to deal with indicators summarized default routes? (Choose the best answer.)


Options are :

  • EIGRP uses a metric worst among all the component routes, while OSPF uses the best metric.
  • EIGRP and OSPF both use among the best metric for all routes in series.
  • EIGRP use the best metric from among all the component routes, while OSPF uses the worst metric
  • None
  • EIGRP and OSPF both use the metric worst among all series of routes.

Answer :EIGRP and OSPF both use among the best metric for all routes in series.

You admit the show ip pim tunnel command Router1, which is the RP. Which of the following appears in the output of show ip pim tunnelcommand? (Choose the best answer.)


Options are :

  • .Both PIM encapsulation tunnel interface and PIM decapsulation tunnel interface
  • Neither PIM encapsulation tunnel interface and PIM decapsulation tunnel interface
  • Only PIM encapsulation tunnel interface
  • None
  • Only PIM decapsulation tunnel interface

Answer :.Both PIM encapsulation tunnel interface and PIM decapsulation tunnel interface

Which of the following should you do in order to drop the unencrypted traffic sent a member of an unregistered group? (Choose the best answer.)


Options are :

  • Removes Fail-Close feature.
  • .Enable SAR.
  • None
  • Removes the SAR.
  • Contact Fail-Close feature.

Answer :Contact Fail-Close feature.

400-101 CCIE Routing and Switching Written Practice Exam Set 6

Which of the following terms refers to the method used to transport IPv6 traffic over an IPv4-only network? (Choose the best answer.)


Options are :

  • 4to6 tunneling
  • 6to4 tunneling
  • None
  • .NAT64
  • dual stacks

Answer :6to4 tunneling

You grant the monitor session 1 source interface FastEthernet1 / 0 SWITCH command. Which of the following statements is true? (Choose the best answer.)


Options are :

  • FastEthernet1 / 0 interface can be a SPAN destination port.
  • FastEthernet1 / 0 interface runs only SPANrelated traffic
  • None
  • FastEthernet1 / 0 interface can coexist with SPAN source VLAN.
  • FastEthernet1 / 0 interface can be a SPAN source port.

Answer :FastEthernet1 / 0 interface can be a SPAN destination port.

Which of the following statements is true regarding the use of the network command OSPFv3 and EIGRPv6? (Choose the best answer.)


Options are :

  • The network command is required EIGRPv6 but not required OSPFv3
  • The network command is required OSPFv3 but not required EIGRPv6
  • The network command is required OSPFv3 does not EIGRPv6.
  • The network command is required, as well as OSPFv3 and EIGRPv6.
  • None

Answer :The network command is required OSPFv3 does not EIGRPv6.

400-101 CCIE Routing and Switching Written Practice Exam Set 6

Which of the following statements best describes the effect of EIGRP neighbor command interface? (Choose the best answer.)


Options are :

  • It takes to send and receive both unicast and multicast packets.
  • It takes to send and receive unicast packets only.
  • It takes to send and receive multicast packets only.
  • It transmits only unicast packets, but receive both unicast and multicast packets.
  • None

Answer :It takes to send and receive unicast packets only.

Realize your MPP, enter the following commands Router1: Router1 (config) #controlplane host Router1 (config-cp-host) # interface management FastEthernet0 / 1 allow ssh Which of the following statements is correct? (Select two options.)


Options are :

  • Only SSH packets Fa0 / 1 can be managed remotely via Router1.
  • .Fa0 / 1 accepts the normal data traffic.
  • .Fa0 / 1 will only accept SSH packages.
  • Fa0 / 1 is set outofband management.
  • SSH traffic can not receive any other interfaces.

Answer :Only SSH packets Fa0 / 1 can be managed remotely via Router1. .Fa0 / 1 accepts the normal data traffic.

By default, what happens when you start the Cisco router if the startup configuration in NVRAM has been corrupted? (Choose the best answer.)


Options are :

  • Startup configuration is loaded from flash memory.
  • System Configuration Dialog starts.
  • .A generic startup configuration is loaded from the disk
  • None
  • Startup configuration can be downloaded from the TFTP server.

Answer :System Configuration Dialog starts.

400-101 CCIE Routing and Switching Written Practice Exam Set 5

Two routers have established a VPN tunnel. Both routers support IPSec and GRE, and both routers configured with IPv4 and IPv6 addresses. You acknowledge tunnel Automatic command on both routers. Which of the following statements is true? (Choose the best answer.)


Options are :

  • The tunnel is not created, because one of the router must be configured statically.
  • GRE tunneling is used and the IPv4 protocol is used for transfer.
  • IPSec tunneling is used, and the IPv4 protocol is used for transfer.
  • GRE tunneling is used, and IPv6 protocol is used for transfer.
  • IPSec tunneling is used, and IPv6 protocol is used for transfer.

Answer :The tunnel is not created, because one of the router must be configured statically.

You 802.1X authentication on Fast Ethernet port 0/1 in switch Switch. You want to make sure that all the hosts connected to port 802.1X authenticated before the hosts can send data to the switch. Which of the following scripts should give a Switch? (Choose the best answer.)


Options are :

  • Switch # configure terminalSwitchA (config) #aaa newmodel Switch (config) #aaa authentication dot1x default group radius Switch (config) # dot1x systemauthcontrol Switch (config) #interface Fast Ethernet 0/1 Switch (configif) # dot1x portcontrol car
  • Switch # specifies terminalSwitchA (config) #aaa newmodel Switch (config) #aaa authentication dot1x default group radius Switch (config) # dot1x systemauthcontrol Switch (config) #interface 0/1 Fast Ethernet Switch (configif) # dot1x all portcontrol
  • Switch # specifies terminalSwitchA (config) #aaa newmodel Switch (config) #aaa authentication dot1x default group radius Switch (config) # dot1x systemauthcontrol Switch (config) #interface 0/1 Fast Ethernet Switch (configif) # dot1x portcontrol forceunauthorized
  • Switch # specifies terminalSwitchA (config) #aaa newmodel Switch (config) #aaa authentication dot1x default group radius Switch (config) # dot1x systemauthcontrol Switch (config) #interface 0/1 Fast Ethernet Switch (configif) # dot1x portcontrol forceauthorized

Answer :Switch # configure terminalSwitchA (config) #aaa newmodel Switch (config) #aaa authentication dot1x default group radius Switch (config) # dot1x systemauthcontrol Switch (config) #interface Fast Ethernet 0/1 Switch (configif) # dot1x portcontrol car

Which statements are true regarding the editing and traffic police traffic? (Select two options.)


Options are :

  • Traffic police can only use the incoming traffic
  • Traffic policing can be used on both inbound and outbound traffic.
  • Traffic shaping can be used only for outbound traffic
  • traffic shaping only incoming traffic can be used.
  • Traffic shaping can be used for both incoming and outgoing traffic.
  • Traffic police can use only outbound traffic.

Answer :Traffic policing can be used on both inbound and outbound traffic. Traffic shaping can be used only for outbound traffic

400-101 CCIE Routing and Switching Written Practice Exam Set 2

You manage the router, which receives four path to your destination network: an internal EIGRP route, an external EIGRP route, OSPF route, and internal BGP route. Which of the following statements is correct? (Choose the best answer.)


Options are :

  • Memory failure.
  • Rib fail.
  • None
  • All routes are placed in the routing table
  • OSPF route is placed in the routing table.

Answer :Rib fail.

Which of the following statements best describes the BGP split-horizon rule? (Choose the best answer.)


Options are :

  • None
  • Routes learned from eBGP do not advertise iBGP peers.
  • Routes learned iBGP do not advertise iBGP peers.
  • Routes learned iBGP do not advertise eBGP peers.
  • .Routes learned from eBGP do not advertise eBGP peers.

Answer :Routes learned iBGP do not advertise iBGP peers.

Which of the following is the VLAN name VLAN 1004? (Choose the best answer.)


Options are :

  • None
  • .token-ring-default
  • trnet-default
  • FDDI-default
  • .fddinet-default

Answer :.fddinet-default

400-101 CCIE Routing and Switching Written Practice Exam Set 5

Which of the following should be considered first when an MLP bundle names to create a network in which multiple clients can use the same username? (Choose the best answer.)


Options are :

  • Password
  • None
  • user name
  • Mac address
  • endpoint discriminator

Answer :endpoint discriminator

You are configuring the router EEM. You agree event ioswdsysmon SUB1 mem-proc function name Task1 cr ge val 30 is a true-time command 200 percent. When is the event function is triggered for Task1 in the process? (Choose the best answer.)


Options are :

  • when the CPU usage increases 30 percent or more during the second period 200
  • .When the use of the memory will increase by 30 percent or more over a time period of 200 second
  • the use of a memory is reduced to 30 percent or more during the 200 msec time period
  • when the CPU usage is reduced to 30 percent or more during the 200 millisecond time
  • None

Answer :.When the use of the memory will increase by 30 percent or more over a time period of 200 second

Which of the following reasons would be the multicast host sends a packet to 235.77.34.2? (Select two options.)


Options are :

  • correspond to the general survey
  • to join the multicast group 235.77.34.2
  • leave the multicast group 235.77.34.2
  • send a general query

Answer :correspond to the general survey to join the multicast group 235.77.34.2

400-101 CCIE Routing and Switching Written Practice Exam Set 2

Cisco ACI, which is the EPG? (Choose the best answer.)


Options are :

  • None
  • a collection of rules and policies that define how endpoints can communicate
  • a collection of VRF instances or IP-address space
  • a collection of endpoints that provide the same function
  • a collection of groups, their connections, and related policies

Answer :a collection of endpoints that provide the same function

Which of the following services is usually done with IaaS vendor? (Select two options.)


Options are :

  • network infrastructure
  • computing and storage resources
  • .käyttöjärjestelmät
  • software applications
  • databases

Answer :network infrastructure computing and storage resources

Which of the following statements are true with respect to netconf? (Select two options.)


Options are :

  • Netconf is a connectionless protocol.
  • Netconf uses XML data modeling language.
  • Yang netconf used as data modeling language.
  • Netconf is standardsbased protocol.
  • Netconf is an open source cloud computing platform.

Answer :Yang netconf used as data modeling language. Netconf is standardsbased protocol.

400-101 CCIE Routing and Switching Written Practice Exam Set 6

Which of the following ports is not TACACS + uses the AAA? (Choose the best answer.)


Options are :

  • TCP 1812
  • TCP 49
  • None
  • UDP 1645
  • UDP 1646

Answer :TCP 49

You provide any service tcpsmallservers command on a Cisco router. Which of the following servers disable command? (Choose 3 options.)


Options are :

  • reject
  • echo
  • BOOTP
  • charg

Answer :reject echo charg

Which of the following commands to create gender-priced, dual-bucket, three-color policer? (Choose the best answer.)


Options are :

  • police cir 50000 100000 PIR-operation in accordance with the transmission exceed-action set DSCP af21 transmission break-action drop
  • None
  • Police 100000 5000 8000 in accordance with the operation exceeds the transmission-action set-DSCP af21 transmission
  • Police CIR 50000 BC 50000 100000 PIR-operation in accordance with the transmission exceeds the operating SE-tdscptransmit af21
  • Police 100000 5000 8000 in accordance with the operation exceeds the transmission-action set-DSCP af21 transmission violate- drop operation

Answer :Police 100000 5000 8000 in accordance with the operation exceeds the transmission-action set-DSCP af21 transmission violate- drop operation

400-101 CCIE Routing and Switching Written Practice Exam Set 6

Which of the following ports are errdisable state? (Choose the best answer.)


Options are :

  • port configured with just the guard, which stops receiving BPDUs
  • port configured with BPDU guard who starts to receive BPDUs
  • port configured guard loop which stops the receiving BPDUs
  • port configured with loop guard, that starts to receive BPDUs
  • port configured with just the guard, that starts to receive BPDUs

Answer :port configured with BPDU guard who starts to receive BPDUs

Which of the following values ??MPLS label indicates that this character is the last entry of the stack? (Choose the best answer.)


Options are :

  • the value of the TC field 1
  • 0 TTL value in the field
  • the value of the S field of 1
  • the value of the TC field 0
  • the value of the TTL field 255

Answer :the value of the S field of 1

Do you want to transfer more corporate functions to the cloud, such as software development and CRM. You decide to use PaaS provider. Which of the following are you most likely to provide and manage? (Choose the best answer.)


Options are :

  • software development environment
  • CRM application
  • networking infrastructure
  • None
  • operating system

Answer :CRM application

400-101 CCIE Routing and Switching Written Practice Exam Set 5

Which statements are true regarding the graceful restart feature? (Select two options.)


Options are :

  • Graceful restart allows the router continues to forward packets during the restart of the routing process.
  • Graceful restart must specify all the neighbor routers function to work properly.
  • Graceful restart has its own Cisco.
  • Graceful restart only works with OSPF.

Answer :Graceful restart allows the router continues to forward packets during the restart of the routing process. Graceful restart must specify all the neighbor routers function to work properly.

Which of the following provides the benefits of computing the fog? (Choose the best answer.)


Options are :

  • It ensures a reliable connection to the cloud.
  • It allows more data is stored in the cloud.
  • It filters the information before it goes into the cloud.
  • It allows the data sent to the cloud faster.
  • None

Answer :It filters the information before it goes into the cloud.

What is the most feasible of the following describes the distance? (Choose the best answer.)


Options are :

  • best metric along a path to the destination
  • the total metric along the path to the destination
  • the highest metric along the path to the destination
  • reported a smaller distance than the current best path
  • None

Answer :best metric along a path to the destination

400-101 CCIE Routing and Switching Written Practice Exam Set 2

Which of the following steps NAT order of operations always take place before the Address Translation? (Select two options.)


Options are :

  • encryption
  • check output access list
  • encryption
  • check input access list

Answer :encryption check input access list

Which of the following commands should be interface configuration mode connected to an NHRP QoS policy map group? (Choose the best answer.)


Options are :

  • IP NHRP group
  • IP multicast NHRP map
  • None
  • IP NHRP map
  • IP NHRP to map

Answer :IP NHRP to map

Comment / Suggestion Section
Point our Mistakes and Post Your Suggestions